Loewe 51501T02 Silver [13/42] Подготовка к эксплуатации

Loewe 51501T02 Silver [13/42] Подготовка к эксплуатации
13
Подготовка к эксплуатации
Подключение к сети питания
Подключить вилку питания в гнездо, расположенное на
задней стороне плеера (стр. 6), затем включить
большую вилку в розетку питания 220-240 В 50/60 Гц.
Включение/выключение
Переключить пульт ДУ для управления плеером
BluTechVision 3D, кратковременно нажав кнопку
DVD.
BluTechVision 3D включается. Если телевизор
(начиная с L271x/SL 1xx) подключён через HDMI,
то телевизор тоже включается. В противном
случае включить телевизор и установить
соответствующий программный слот AV.
Для вашего телевизора может
потребоваться настроить работу
BluTechVision 3D в соответствии с
используемым аудиовидеогнездом
(см.пункт Управление другими
устройствами”).
Как только BluTechVision 3D будет готов к работе
загорается Рабочий дисплей (стр.6).
Для выключения устройства нажать кнопку
включения/выключения BluTechVision 3D или на
пульте ДУ Assist.
Digital Link HD
С помощью Digital Link HD телевизор Loewe и другие
телевизора с поддержкой стандарта CEC передают
сигналы с пульта ДУ через HDMI-подключение к плееру
BluTechVision 3D.
Телевизор должен быть включён.
Выбрать на телевизоре программный слот AV.
Пока в качестве программного слота выбран HDMI
большинство команд дистанционного управления
телевизором (пульт ДУ ASSIST в режиме TV)
передаётся на подключённое HDMI-устройство.
Громкость, включение/выключение звука, настройства
звука и настройка соотношения сторон однако остаются
для управления телевизором. Аудиокоманды (пульт ДУ
ASSIST в режиме AUDIO) не передаются на телевизор.
Нажатие кнопки TV в течение продолжительного
времени используется для переключения между
режимами управления HDMI и TV.
Кратковременное нажатие кнопки TV
ииспользуется для переключения обратно в
режим телевизора.
При нажатии кнопки TV (кратковременном), в
режим телевизора происходит возврат к
последней просматриваемой станции и
завершение управления устройством.
Может потребоваться обновление
ПО вашего телевизора.
Обращайтесь к вашему ритейлеру.
Digital
Link
HD
(
HDMI
CEC
)
С помощью Digital Link HD телевизоры Loewe TV
(начиная с шасси L271x, версия ПО V9.2) передают
сигналы с пульта ДУ с помощью HDMI-подключения с
телевизоров Loewe TV на совместимые
дополнительные устройства, например BluTechVision
3D. Digital Link HD имеет смысл применять, если вы
хотите осуществить скрытую установку BluTechVision
3D и управлять всеми устройствами с помощью
телевизора Loewe.
Прежде всего необходимо назначить функцию
HDMI CEC пульта ДУ Assist нужной кнопке
устройства (например, DVD) к помощью кода
22 как описано на странице 12.
Затем выполнить назначение функции Digital
Link HD HDMI-интерфейсу используемого
телевизора нажатием определённой ранее
кнопки (например, DVD) в течение 5 секунд.
Отображается меню выбора.
Выбрать нужное оборудование
апример, BluTechVision).
Нажать OK для подтверждения.
Теперь сигналы с пульту ДУ Assist телевизора
Loewe передаются на BlueTechVision 3D, если
соответствующая кнопка устройства
апример, DVD) была предварительно
нажата.
Может потребоваться обновление
ПО вашего телевизора.
Обращайтесь к вашему ритейлеру.
13
Start-up
Connecting to the Mains Supply
Plug the mains plug (page 6) into a mains socket 220-240V/50-60 Hz.
Switching on/off
Set the remote control for BluTechVision 3D operation by
briefly pressing the button DVD.
Your BluTechVision 3D switches on. If you have connected a
Loewe TV set (from L271x/SL 1xx) via HDMI, then this will switch
on as well. Otherwise, switch your TV set on and set the respec-
tive AV programme slot.
For your TV set you may have to adjust operation of BluTechVision
3D to suit the AV socket used (look under e.g.Operating other
devices“ in the respective operating instructions for your TV set.
As soon as BluTechVision 3D is ready to go, the green Operating
Display (page 6) lights up.
To switch the device off, press the On/Off button on the
BluTechVision 3D or on the remote control Assist again.
Digital Link HD
With Digital Link HD, Loewe TV sets and other TV sets supporting the CEC standard
forward the signals from the remote control via the HDMI connection from the TV
set to the BluTechVision 3D.
The TV set must be switched on.
On the TV set, select the AV programme slot for HDMI.
As long as HDMI is selected as the programme slot, most TV remote control
commands (ASSIST in TV mode) will be passed on to the connected HDMI unit.
Volume, sound on/off, sound adjustment and TV aspect ratio however, still affect
operation of the TV set. The AUDIO commands (ASSIST in AUDIO mode) are not
passed on by the TV.
By pressing the TV button for a long time, you can switch between
HDMI and TV operation. Pressing the TV button briefly switches
back to TV mode.
With the TV button (press briefly), in TV operation you switch
back to the last station watched and terminate the device
control.
It is possible that your Loewe TV set may need a software
update. Please contact your specialist retailer.
Digital Link HD (HDMI CEC)
With Digital Link HD, Loewe TV sets (from Mainframe L271x, Software V9.2) pass
the signals from the remote control via the HDMI connection from the Loewe TV
set to compatible additional devices, such as BluTechVision 3D. Digital Link HD
makes sense if you want to set up BluTechVision 3D in a concealed location and
all the devices are to be controlled via the Loewe TV set.
First of all, assign the HDMI CEC function for the Assist
remote control to the desired device button (e.g. DVD) using
Code 22 as described on page 12.
Then carry out the allocation of the Digital Link HD function to
the HDMI interface of the TV set used by pressing the button
set above (e.g. DVD) for 5 sec.
A selection menu will appear.
OK
OK
HINT
Here you select the device which you want to switch over your remote control
to with the key. After confirming the selection with OK all remote control
commands are passed on to the selected device via the TV set in future when
you press this key.
SELECT HDMI DEVICE FOR KEY
DVD
BluTech Vision
No device
Adopt
AUDIO
Select the desired equipment (e.g. BluTechVision).
Confirm OK.
Now, the signals from the Assist remote control of the Loewe
TV set are transmitted to the BlueTechVision 3D if the
relevant device button (e.g. DVD) is pressed beforehand.
It is possible that your Loewe TV set may need a software
update. Please contact your specialist retailer.
13 -

Содержание

Скачать