![Aurora A-1790D [58/151] Sewing data of vdt pattern](/img/pdf.png)
Aurora A-1790D [58/151] Sewing data of vdt pattern
![Aurora A-1790D [58/151] Sewing data of vdt pattern](/views2/1495536/page58/bg3a.png)
Normal Pattern Sewing Computerized Control System for Square Buttonhole Machine
48
4.12.2 Sewing Data of VDT Pattern
Sewing Data List of VDT Pattern：
No. Item Range Unit Initial Value
S03
Right Width of Knife Groove
Set the interval between the knife and right
parallel part.
-2.00~2.00 0.05mm 0
S04
Left Width of Knife Groove
Set the interval between the knife and left
parallel part
-2.00~2.00 0.05mm 0
S81
Knife motion
This item sets "With/without motion" of knife。
：Knife Off
：Knife On
Knife On
S84
Max Speed Limitation
This item sets max speed of the sewing
machine. The value is limited by the K07(Set
maximum speed limitation)
400~4200 100rpm
Parameter
K07
S91
1
st
Pitch Adjustment -9~9 1 针 0
S92
2
nd
Pitch Adjustment -9~9 1 针 0
S93
Scale Ratio（X Direction） 20~200 1% 100
S94
Scale Ratio（Y Direction） 20~200 1% 100
S95
Standard Tension 0~200 1 100
Содержание
- Sc500 1790 p.1
- Version 2013 01 p.1
- Computerized control system for square buttonhole machine p.1
- Forewords p.3
- Safety matters for attention p.5
- Installation p.5
- Before checking adjusting and repair any air driven equipment user needs cut off the source of gas and wait for the pressure indicator drop to 0 p.6
- Sewing p.6
- Safety matters for attention computerized control system for square buttonhole machine p.6
- Maintenance inspection p.6
- Table of content p.7
- General information p.11
- General p.11
- Function and specification p.11
- Working environment p.12
- Standardization p.12
- Matters for safe using p.12
- Installation p.12
- Warning and danger p.13
- Others p.13
- Maintenance inspection and repair p.13
- Abandonment p.13
- The preventions on instruction p.14
- Warning p.14
- Operation method p.15
- Sewing list p.16
- Threading needle thread p.17
- Preparation before sewing p.17
- Needles p.17
- Installation of needle p.17
- In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.17
- Do turn off power when you install p.17
- Installation of bobbin p.18
- In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.18
- If the bobbin is not in the proper position the shuttle core will move at sewing and thread will be wound to shaft the shape of standard shuttle is different from that of non oil shuttle they cannot be used in common p.18
- In straight buttonhole sewing is different from that of zigzag buttonhole p.19
- In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.19
- Attention the threading method at slot p.19
- Adjustment of bobbin thread tension p.19
- Threading at bobbin p.19
- When the chemical thread is used please decrease the tension slightly increase the tension when the cotton thread is used p.20
- Installation of knife p.20
- In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.20
- After adjusting the bobbin thread tension user also needs to check the needle thread tension in the sewing parameters p.20
- Method for adding oil p.22
- In order to avoid the personal injury caused by the sudden start of machine user has to turn off power and make sure the motor stops before performing the following operation p.22
- Operating instruction p.23
- Name an p.23
- Description of each part p.23
- Reset release the error p.24
- Minus decrease the value p.24
- First make sure that the set presser type a is the same as that of the presser actually installed p.24
- Esc quit the current interface at data change interface it is for cancelling the change of data p.24
- Enter confirm the changed data p.24
- Common buttons p.24
- Basic operation p.24
- ② select the wanted pattern no p.24
- ① turn on the power p.24
- When the power is on the data input screen is displayed pattern no button b which is marked at present is displayed in the upper section of the screen press button b to select the pattern no the unregistered pattern no will not be displayed p.24
- The buttons for the common operation in each interface are shown at below p.24
- Plus increase the value p.24
- Operating instruction computerized control system for square buttonhole machine p.24
- Number input display the number keyboard and input the number p.24
- Operation of normal pattern p.25
- Operation of continuous sewing p.27
- Operation of cyclic sewing p.29
- Normal pattern sewing p.32
- Function keys p.32
- Pattern registration p.35
- Pattern copy p.37
- Pattern naming p.38
- Threading p.38
- Winding p.39
- Select the type of presser p.40
- Pattern selection p.41
- Sewing shape selection p.42
- Sewing data setting p.44
- Trial sewing p.52
- Direct selection of pattern p.52
- Set needle thread tension p.54
- Operation of counter p.55
- In case of the radial eyelet shape set the bar tacking tension to approximately 120 and make the balance of stitches p.55
- Emergency stop p.56
- Vdt pattern operation p.57
- Display and operation of vdt pattern p.57
- Sewing data of vdt pattern p.58
- Continuous sewing p.59
- Function list p.59
- Selection of continuous sewing pattern p.60
- Edition of continuous sewing pattern p.60
- Edition of continuous sewing p.60
- Continuous sewing pattern registration p.63
- Continuous sewing pattern copy p.64
- Deletion of continuous sewing pattern p.65
- Function list p.68
- Continuous sewing interface p.68
- Trial sewing for continuous sewing p.69
- Function list p.72
- Cyclic sewing p.72
- Pattern registration p.73
- Edition of cyclic sewing p.73
- Pattern copy p.74
- Edition of cyclic sewing pattern p.75
- Selection of cyclic sewing pattern p.75
- Change fabric p.77
- Function list p.78
- Cyclic sewing interface p.78
- Trial sewing at cyclic sewing p.80
- Mode setting p.82
- Function list p.83
- Level 1 parameter setting p.84
- Level 2 parameters setting p.88
- Counter setting p.91
- Functions p.92
- Settings on user management p.93
- Edition of sewing data p.94
- Register pattern to direct button p.95
- Change sewing mode p.95
- 1 adjustment of needle thread trimming p.97
- Test mode p.97
- 3 input signal test method p.98
- 2 adjustment of down thread trimmer p.98
- 4 inspection of lcd display p.99
- 6 output inspection p.100
- 5 correction of touching panel p.100
- 8 continuous running p.101
- 7 speed test p.101
- Operation of keyboard lock p.102
- Brightness adjustment p.102
- Initialization p.104
- Parameter back up restoration p.106
- Operations p.108
- Communication p.108
- About the available data p.108
- Pattern transfer p.109
- Parameter transfer p.111
- Software update p.112
- Information p.114
- Check the maintenance information p.114
- Set the maintenance time p.116
- Method to release the warning p.117
- Via information interface p.118
- Information of production control p.118
- Via sewing interface p.119
- Setting of production control information p.120
- Threading figure p.123
- Warning record p.124
- Running record p.125
- Setting of periodical password p.126
- Warning list p.134
- Appendix 1 p.134
- Hint list p.135
- Common problems and solutions p.137
- Default values of sewing shapes p.140
- Installation size of control box p.149
- Appendix 2 p.149
- Installation size of operation panel p.150
- System diagram p.151
Похожие устройства
-
Aurora А-782DИнструкция к блоку управления -
Aurora А-782DИнструкция по эксплуатации -
Aurora А-781DИнструкция к блоку управления
-
Aurora А-781DИнструкция по эксплуатации
-
Aurora A-9820Руководство по эксплуатации -
Aurora A-1790DРуководство по эксплуатации -
Aurora A-783DИнструкция к блоку управления
-
Aurora A-783DИнструкция по эксплуатации
-
Aurora A-782DИнструкция по эксплуатации -
Aurora A-782DИнструкция к блоку управления -
Aurora A-781DИнструкция к блоку управления -
Aurora A-781DИнструкция по эксплуатации