![Brother PJ-723 [26/59] Vt perform vertical tab](/img/pdf.png)
Brother PJ-723 [26/59] Vt perform vertical tab
![Brother PJ-723 [26/59] Vt perform vertical tab](/views2/1897103/page26/bg1a.png)
ESC/P Legacy Command Reference
- 13 -
5. Control Command Details
5.3 Tab setting commands
ESC B Specify vertical tab position
ASCII: ESC B n n... NUL
Decimal: 27 66 n n... 0
Hexadecimal: 1B 42 n n... 00
Function
Specifies a vertical tab position.
Details
Specifies a vertical tab at the position where
(line feed amount when this command is specified) * (specified number of lines n).
A maximum of 16 tab positions can be specified.
A tab setting that specifies a position extending past the bottom margin is ignored.
If n = 0, the vertical tabs are cancelled (default), as when the VFU tab is set to channel 0.
VT Perform vertical tab
ASCII: VT
Decimal: 11
Hexadecimal: 0B
Function
Prints the data in the print buffer, and feeds the paper to the next vertical tab position.
Details
Vertical tab position = Line feed amount when this command is specified * Specified number of lines
If the remaining length of paper is not enough to perform a vertical tab, an FF operation is performed
according to the specified form feed mode.
If VT is received when no vertical tabs are specified, an LF operation is performed.
If VT is entered after the vertical tab positions are cleared with ESC B NUL, the operation that is
performed is the same as CR.
The “specify auto-cancelling double-width characters” command is cancelled.
Содержание
- Version 1 0 p.1
- Software developer s manual p.1
- Pj 722 723 762 763 763mfi 773 p.1
- Esc p legacy command referencepj 722 723 762 763 763mfi 773 p.1
- Esc p legacy command reference p.1
- Condition of use p.3
- No warranty p.3
- Important please read carefully p.3
- Contents p.4
- Introduction p.6
- What is esc p p.7
- Using esc p legacy commands p.8
- Examples of using esc p legacy commands p.10
- Esc i a 00h p.10
- Viii 2 examples of using esc p legacy commands p.11
- This is the document that will be made p.11
- Step 1 specify the horizontal position p.11
- In order to make this document the following two steps are required p.11
- Esc 3ch 00h p.11
- Step 2 select the font type p.12
- Ix 2 examples of using esc p legacy commands p.12
- Esc k 00h p.12
- Esc k 00h p.13
- Esc i a 00h p.13
- Esc 3ch 00h p.13
- At your side p.13
- Print area p.14
- Esc p legacy command limitations p.14
- Resolution p.16
- Characters p.16
- Control code list p.17
- Paper feed commands p.20
- Ff form feed p.20
- Cr carriage return p.20
- Control command details p.20
- Lf line feed p.21
- Esc 0 specify line feed of 1 8 inch p.21
- Esc 2 specify line feed of 1 6 inch p.22
- Esc 3 specify line feed of n 180 inch p.22
- Esc specify line feed of n 360 inch p.23
- Esc j specify forward paper feed of n 180 inch p.23
- Esc a specify line feed of n 60 inch p.23
- Print area setting commands p.24
- Esc c specify page length in lines p.24
- Esc c 0 specify page length in inches p.24
- Esc o cancel skip perforation p.25
- Esc n specify skip perforation p.25
- Vt perform vertical tab p.26
- Tab setting commands p.26
- Esc b specify vertical tab position p.26
- Ht perform horizontal tab p.27
- Esc d specify horizontal tab position p.27
- Print position setting commands p.28
- Esc l specify left margin p.28
- Esc q specify right margin p.29
- Esc specify absolute position p.30
- Bs backspace p.30
- Esc specify relative position p.31
- Esc p specify 10 cpi p.32
- Esc m specify 12 cpi p.32
- Esc k select font p.32
- Character selection commands p.32
- Esc p apply cancel proportional characters p.33
- Esc g specify 15 cpi p.33
- Esc t cancel superscript subscript p.34
- Esc s apply superscript subscript p.34
- Esc t select character code table p.35
- Esc r select international character set p.36
- Esc x select text quality p.37
- Character style commands p.37
- Si esc si specify reduced characters p.37
- So esc so specify auto canceling double width characters p.38
- Dc4 cancel auto canceling double width characters p.38
- Dc2 cancel reduced characters p.38
- Esc w specify cancel double width characters p.39
- Esc w specify cancel double height characters p.39
- Esc f cancel bold style p.40
- Esc e apply bold style p.40
- Esc h cancel double strike printing p.41
- Esc g apply double strike printing p.41
- Esc sp specify character spacing p.42
- Esc apply cancel underlining p.42
- Esc q select character style p.43
- Esc 5 cancel italic p.43
- Esc 4 apply italic p.43
- Esc global formatting p.44
- Esc apply cancel download character set p.45
- Esc 0 define download characters p.45
- Character definition commands p.45
- Esc 7 apply upper control codes p.46
- Esc 6 cancel upper control codes p.46
- Esc 0 copy character set p.46
- Supplemental function commands p.47
- Esc initialize p.47
- Others p.48
- Esc l 8 bit double density bit image p.48
- Esc k 8 bit single density bit image p.48
- Esc y 8 bit double speed double density bit image p.49
- Esc z 8 bit quadruple density bit image p.50
- Esc select bit image p.50
- Esc select vfu channel p.51
- Esc convert bit image p.51
- Esc b specify vfu tab position p.52
- Esc i a switch command mode p.53
- Advanced commands p.53
- Esc i s request printer status p.54
- Esc e f 1 reverse feed p.54
- Character code tables p.55
- Appendix a character code tables p.55
- Appendix b introducing the brother developer center p.58
- Brother us eng p.59
Похожие устройства
-
Brother PJ-723Интерактивное руководство пользователя -
Brother PJ-723Справочник по языку команд Brother ESC -
Brother PJ-723Руководство по шаблонам P_touch -
Brother PJ-723Справка по растровым командам -
Brother RJ-4040Краткий справочник -
Brother RJ-4040Руководство по безопасности устройства -
Brother RJ-4040Руководство по использованию AirPrint -
Brother RJ-4040Руководство по использованию программного обеспечения -
Brother RJ-4040Руководство пользователя по работе в сети -
Brother RJ-4040Руководство пользователя -
Brother RJ-4030Краткий справочник
-
Brother RJ-4030Руководство по безопасности устройства