Home
Главная
Nemox
Фризер для мороженого
Gelato 5+5K Crea Twin
Руководство по эксплуатации Страница: 6

Nemox Gelato 5+5K Crea Twin Руководство по эксплуатации онлайн [6/64] 772907

EnglishEnglish EnglishEnglish

Of the preparation is excessive, thus while mixing.

preventing compromising the mechanical •For the preparation of Granitas, the maximum

functions of the machine. The cooling system recommended amount is 1kg. mixed with the

will continue to run until it is manually stopped. paddle provided. It can process up to 1.5kg. of

•In automatic mode, you can first choose one of Granita using the special Granita paddle that

the 4 programs available (classic Italian can be purchased separately.

gelato, semi-soft gelato, Granita, fast cooling) •It is recommended to pour the mixture at a

and 4 preservation programs for every temperature between +10°C and +20°C.

production type. Higher temperatures may also considerably

With this operating mode you will not have to increase the processing time.

worry about anything, once the selections are

DIRECTIONS FOR USE

made and the ice cream machine is started, it

•GELATO 5+5 K TWIN CREA is composed of

produces ice cream and automatically

two identical groups which are totally

switches to the desired preservation mode.

independent and autonomous: here is

You just have to serve the ice cream to your

illustrated the operation of the single group.

customers, always with the correct

•Check that the voltage indicated on the data

consistency.

plate corresponds to the local network. Insert

FIRST USE the power plug into the power outlet and

•Place GELATO 5+5K TWIN CREA on a flat operate the main switch (10); the light will

surface, make sure that the ventilation grids (6) indicate the presence of voltage. The

are not obstructed. Leave a minimum electronic board will run an initialization check,

clearance of 10 cm. around the ventilation triggering all the LEDs on the control panel in

grids. sequence.

•During use, the appliance must be kept clear •Insert the mixing paddle (5) in the pot, turning it

of walls or furniture so as to not obstruct the clockwise until it is positioned in the bottom of

inflow and outflow of cooling air. The leakage the pot.

of warm or hot air is an integral part of the •Tighten the locking ring (4) to the bottom so

operation of the device, that exchanges heat that the mixing paddle is securely attached.

with the outside for refrigeration. •Pour the previously prepared mixture.

•Leave the machine in a horizontal position for 8 •Close the lid (3).

hours or more before first use, as if it has been

MANUAL MODE

tilted during transport, the cooling agents

•Start the cooling system by pressing the

must re-settle in the correct position.

Button (1); the LED (1a) will light up.

•Before starting to use the machine, carefully

IMPORTANT: if the machine is turned off due to

clean the parts that are in direct or indirect

sudden and temporary suspension of power

contact with processed foods (pot, mixing

supply or incorrect operation using the power

paddle, paddle inserts, locking ring, lid etc).

keys of the refrigerant, wait a few minutes

•Hygiene is extremely important when dealing

before restarting.

with food. Carefully follow the provisions of

•Press button (2) to start the paddle; the LED

hygiene standards applicable in your country

(2a) lights up, the production cycle begins.

(HACCP or equivalent).

The preparation time varies depending on the

PREPARING THE MIXTURE quantity, initial temperature of the mixture,

Select the recipe and prepare the mixture, product type (creamed, sorbet or Granita) and

paying attention to the following: ambient temperature.

•Handle the ingredients as required by the IMPORTANT: The movement of the paddle is

hygiene standards applicable in your country entirely independent of the cooling system. A

(HACCP or equivalent). safety device stops the movement of the paddle

•For the preparation of ice creams and sorbets, when the lid is lifted.

do not introduce more than 1.25kg of mixture, If the lid remains raised for prolonged periods,

in order to allow for proper volume increase the cooling system will continue to operate.

In automatic mode

DIRECTIONS FOR USE

GELATO 5+5 K TWIN CREA

FIRST USE

GELATO 5+5K TWIN CREA

MANUAL MODE

IMPORTANT:

PREPARING THE MIXTURE

IMPORTANT:

do not introduce more than 1.25kg of mixture

Consequently, when the lid is lowered again the programs in sequence.

paddle may not start or stop due to the

•When the LED becomes steadily lit, the

excessive consistency of the mixture. In this

associated program starts up and begins the

case, the electronic control will permanently

production cycle.

stop the paddle and LED (2a) will flash to

•The machine has 4 production programs and

indicate the fault.

4 preservation cycles for each of them. When

If the preparation is not yet complete, turn off the

the program selected starts up you can

compressor by pressing the button (1) and the

choose the preservation cycle desired. Chose

paddle via the button (2), wait until the mixture

the preservation cycle by pressing the button

becomes softer and restart production.

(12) repeatedly. When switching from the first

•According to the recipe and the amount of preservation program to the fourth, gelato

ingredients used, average production time is consistency increases gradually.

15/20 minutes.

•When the ice cream reaches the right

•Through the opening (3a) on the lid, you can consistency, the production program stops

add additional ingredients (e.g. to make ripple automatically and the preset preservation

ice cream during the last preparation phase). cycle is enabled.

•When the preparation has reached the •Every production program has a preset

desired consistency, turn off the cooling threshold time after which the machine enters

system by pressing button (1) and stop the in preservation cycle, regardless of the current

paddle by pressing button (2). To easily production phase.

remove the preparation from the pot, remove

•If deemed appropriate, it is possible to enable

the mixing paddle (5) by loosening the

the selected preservation cycle at any time ,

appropriate locking ring (4).

ending the production program. Select the

preservation cycle desired via the key 12

MANUAL START OF THE PRESERVATION

(sequence selection). Keep the paddle button

CYCLE

(2) an compressor button (1) pressed

•Should it become necessary to start the

simultaneously for 3 seconds. The machine

preservation cycle manually, you can do this at

will immediately switch from production cycle

any time. Keep paddle button (2) and

to preservation cycle.

c o m p r e s s o r b u t t o n ( 1 ) p r e s s e d

•CLASSIC ITALIAN GELATO AND SORBET

simultaneously for 3 seconds. The machine

PROGRAM. By pressing button (11) once, the

will immediately switch to preservation cycle

LED (11a) will light up and activate the

related to the classic Italian gelato production

production program. At the end of the

program. The LED (12a) will turn on.

production cycle, the LED (11a) flashes

•Should you need to run a preservation cycle

indicating that the selected preservation cycle

related to a different production program,

has been activated.

before switching from manual mode to

If the preparation was ready before reaching

preservation mode, select the desired

the operation time limit, the whipping paddle

prod uctio n progr a m (see s ectio n

locks. The preservation function is

"CHANGING THE PRESERVATION CYCLE").

automatically activated.

AUTOMATIC MODE

•SEMI-SOFT GELATO PROGRAM. By pressing

The GELATO 5+5K TWIN CREA machine has a

button (11) twice, LED (11b) will light up and

series of programs which automate the

activate the processing program. At the end of

production and preservation process.

the production cycle, the LED (11b) flashes

•Follow the steps described in the section

indicating that the selected preservation cycle

"DIRECTIONS FOR USE".

has been activated.

•Press button (11) to start up the machine in

If the preparation was ready before reaching

automatic mode by selecting the first

the operation time limit, the whipping paddle

operation program. The LED flashes for 3

locks. The preservation function is

seconds during which, if you keep on pressing

automatically activated.

the button (11), you will be able to select other

MANUAL START OF THE PRESERVATION

CYCLE

CLASSIC ITALIAN GELATO AND SORBET

PROGRAM

AUTOMATIC MODE

SEMI-SOFT GELATO PROGRAM

GELATO 5+5K TWIN CREA

Nemox Gelato 5+5K Crea Twin Руководство по эксплуатации онлайн [6/64] 772907

Похожие устройства