Rondell RDE-1504 Инструкция по эксплуатации онлайн [10/24] 810687
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Rondell RDE-1504 Инструкция по эксплуатации онлайн [10/24] 810687

Rondell RDE-1504 Инструкция по эксплуатации онлайн [10/24] 810687
10
ENGLISH
THIS UNIT IS INTENDED FOR HOUSEHOLD USE ONLY. ITS
COMMERCIAL USAGE AND USAGE IN PRODUCTION AREAS
AND WORK SPACES IS PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low temperature
keep it for at least three hours at room temperature before
switching on.
•
Unpack the juice extractor.
Disassemble and clean the juice extractor before usage:
•
Remove the pusher (1) from the lid (3) feeding chute (2).
•
Lower the locks (7) and remove the lid (3).
•
Remove the grating filter (4) holding it by the juice collec-
tor (5).
•
Remove the juice collector (5).
•
Wash thoroughly and dry all the removable parts (1, 3, 4, 5, 11)
that will contact products.
Note: Be cautious when holding the grating filter (4) in your
hands, as the disc grating surface is very sharp.
MAKING JUICE
Before the first plugging in make sure that the operating voltage
of the unit corresponds to the voltage of your mains.
Fruit and vegetables meant for processing must be fresh.
Before juice extracting wash fruit/vegetables, remove inedi-
ble parts from vegetables or fruit, such as stems, hard peel or
stones, for example, of cherry or peach, cut them into pieces
easily fitting into the feeding chute (2).
•
Place the motor unit (8) on a dry, flat and steady surface.
•
Before the unit assembling make sure that the operation
mode switch (9) is set to the position «0», and the plug is not
inserted into the mains socket.
•
Check and set the juice draining spout (6) to the lower posi-
tion, where necessary.
•
Install the juice collector (5) on the motor unit (8) so that the
grooves in the lower part of the juice collector (5) tightly fix
the pulp compartment (10).
•
Install the grating filter (4) at the juice collector (5) until a dis-
tinctive click of the lock.
ATTENTION! Do not use the juice extractor if you find
mechanical damages of the grating filter (4).
•
Install the lid (3) on the juice collector (5) and fix it with the
lock (7).
•
Set the juice cup (11) under the juice draining spout (6).
•
Unlock the juice draining opening by pressing the spout (6)
downwards, if it has been in the upper position.
•
Insert the power plug into the mains socket.
•
Switch the juice extractor on by setting the switch (9) to the
position «1» (low speed) or to position «2» (high speed).
•
After the juice extraction press the spout (6) upwards to
block the juice dropping out of the juice extractor.
Notes:
Low speed «1» is intended for extracting juice from soft veg-
etables/fruits, such as tomatoes, ripe pears, strawberries,
oranges, plums, grapes, pumpkins, onions, cucumbers etc.
High speed «2» is intended for extracting juice from hard veg-
etables/fruits, such as artichoke, carrot, apples, capsicum,
beet, potatoes, pineapples, vegetable marrows, celery, spin-
ach, dill, leek etc.
ATTENTION! To avoid the grating filter (4) stopping and motor
rotor jamming during the processing of viscous or quite hard
food it is recommended to use the high speed operation mode
«2» of the juice extractor.
•
The juice extractor will be switched on only if all removable
parts are installed properly, and the lid (3) is fixed with the
lock (7).
•
After switching on wait at least 5 seconds until the motor
speed accelerates.
•
Feed fruit/vegetable pieces into the lid (3) feeding chute (2)
only when the grating filter (4) is rotating.
•
Gradually put vegetables or fruits cut beforehand into the lid
(3) feeding chute (2) and push them gently with the pusher
(1). Do not press on the pusher (1) too hard as it can lead to
decrease of juice amount as well as stop the grating filter (4)
rotation. The slower is the fruit and vegetables processing,
the higher is the juice extraction rate.
•
Do not put your fingers or any other foreign objects into the
lid (3) feeding chute (2).
•
During operation, check the grating filter (4) periodically for
obstruction of the mesh with pulp, if necessary wash the
grating filter (4); before removing the grating filter (4), switch
the juice extractor off and unplug it.
•
Control the pulp compartment (10) filling, if the compart-
ment (10) is filled up, switch the juice extractor off, unplug it
and remove the pulp.
ATTENTION!
To extend the safe operation period of the unit is recom-
mended 1 minute stop after 1 minute operation of the juice
extractor. After 3 such operation cycles let the unit cool down
for 15 minutes.
The juice extractor is equipped with an automatic safety device
which protects the motor from overheating damage while
working at maximum capacity. This protection automatically
switches the juice extractor off when the motor overheats.
Should this occur, unplug the juice extractor and wait for the
motor to cool down.

Похожие устройства

Скачать