Home
Главная
Coolfort
Утюг
CF-3410
Инструкция по эксплуатации Страница: 9

Coolfort CF-3410 Инструкция по эксплуатации онлайн [9/28] 811800

ENGLISH

• Check the unit for damages, do not use the iron in case

of damages.

• Before switching the iron on, make sure that your home

mains voltage corresponds to the iron operating voltage.

• The unit is intended for operation with AC system and

50 or 60 Hz frequency. The unit does not need any

additional settings for operating with the required nomi-

nal frequency.

• There may be water residue in the tank (10), this is nor-

mal, as the iron has undergone factory quality control.

Note: While the first switching on the heating element of

the iron burns, therefore occurrence of foreign smell and a

small amount of smoke is possible, it is normal.

Control knobs and symbols

• Burst of steam button (3) – press the button to activate

the additional steam supply function.

• Water spray button (4) – press the button to activate the

water spray function for dampening the fabrics.

• Temperature control knob (10) – allows to set the iron

soleplate temperature depending on the type of fab-

ric (see the table below). The knob is in the position

«MIN» – the iron is off.

• Continuous steam supply knob (11) – with a smooth

adjustment of the steam supply

– in the « » position of the knob (11), the steam sup-

ply is turned off;

– in the « » position of the knob (11), the maximum

steam supply is turned on.

• «Clean» self-cleaning button of the steam chamber of

the iron (12) - in the self-cleaning mode, press and hold

the «clean» button (12).

• «MAX» maximum water level mark (13).

WATER SELECTION

You can use tap water to fill the water tank (9). If tap water

is hard, use distilled or demineralized water, this will prolong

service life of the iron.

Note: Do not fill the water tank (9) with scented liquids, vine-

gar, starch solution, descaling reagents, chemical agents etc.

FILLING THE WATER TANK

Before filling the iron with water, make sure that it is

unplugged.

• Set the temperature control knob (10) to the position

«MIN», and the continuous steam supply knob (11) to

the position « » – continuous steam supply is off.

• Open the water inlet lid (2) and pour water into the

water tank (9) using the beaker (15) and then close the

lid (2) tight.

Notes:

– Do not exceed the «MAX» mark (13).

– If you need to refill water during ironing, always switch

the iron off at first and unplug it.

– After you finish ironing, switch the iron off, wait until it

cools down completely, then open the water inlet lid (2),

turn over the iron and drain the remaining water.

IRONING TEMPERATURE

Before operation, test the heated iron on a piece of cloth

to be sure that the iron soleplate (14) and the water tank

(9) are clean.

• Always check the recommended ironing temperature

indicated on the tag before ironing.

• If the item label is marked with the symbol « », do

not iron the item.

• If there is no tag with recommended ironing tempera-

ture, but you know the type of fabric, use the following

table to determine the proper temperature.

Ironing temperature table

Icons Fabric type (temperature)

do not iron

•

Synthetics, nylon, acryl, polyester

(low temperature)

••

Silk/wool (medium temperature)

•••

Cotton (high temperature)

МАХ

Linen (high temperature)

• This table is only valid for smooth materials. Fabrics of

other types (crimped, raised, etc.) are best ironed at

low temperature.

• Sort items by ironing temperature first: synthetics to

synthetics, wool to wool, cotton to cotton etc.

• The iron heats up faster than it cools down. For this rea-

son, it is recommended to iron the items which require

low temperature first (for instance, synthetic fabrics).

After that, start ironing at higher temperature (silk/

wool). Cotton and linen items should be ironed last.

• If an item is made of mixed fabrics, the iron should be

set to the lowest temperature (for instance, if an item is

60% polyester and 40% cotton, it should be ironed at

temperature used for polyester ironing «•»).

• If you cannot define the fabric structure, find a spot that

is inconspicuous when the item is being worn and select

the ironing temperature experimentally (always start

with the lowest temperature and raise it gradually until

you get the desired result).

• Corduroy and other fabrics that become glossy quickly

should be ironed strictly in one direction (in the direction

of the pile) with slight pressure.

• To avoid appearance of glossy spots on synthetic and

silk fabrics, iron them backside.

SETTING THE IRONING TEMPERATURE

• Place the iron on its base (8).

• Insert the power plug into the mains socket.

• Turn the control knob (10) to set the required ironing

temperature: «•», «••», «•••» or «MAX», depending

on the type of fabric, the indicator (5) will light up.

• Once the temperature of the soleplate (14) reaches

the set point, the indicator (5) will go out and you can

start ironing.

Note: If you are ironing at high temperature but you need

to switch to lower temperature, wait until the soleplate

temperature decreases and the indicator (5) lights up, and

only then you may start ironing.

WATER SPRAY

• You can dampen the fabric by pressing the water spray

button (4) several times.

• Make sure that there is enough water in the water tank (9).

Coolfort CF-3410 Инструкция по эксплуатации онлайн [9/28] 811800

Похожие устройства