IMS SPOT 3900 -230V 019355 Инструкция онлайн [10/60] 816329
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

IMS SPOT 3900 -230V 019355 Инструкция онлайн [10/60] 816329

IMS SPOT 2700 -230V 055360 Инструкция онлайн [10/60] 816328
STANDARD
GENERAL INSTRUCTIONS
Read and understand the following safety instructions before use.
Any modication or maintenance not specied in the instructions manual should not be undertaken.
The manufacturer is not liable for any injury or damage due to non-compliance with the inructions featured in this manual.
In the event of problems or uncertainties, please consult a qualied person to handle the inallation properly.
Make sure to keep the inructions as you might need to refer to them later.
These inructions cover the material in the condition it was delivered. It is the responsibility of the user to carry a risk analysis in
case the inructions are not followed.
ENVIRONMENT
This equipment mu only be used for welding operations in accordance with the limits indicated on the descriptive panel and/or in
the user manual. Safety inructions mu be followed. In case of improper or unsafe use, the manufacturer cannot be held liable.
This equipment mu be used and ored in a room free from du, acid, ammable gas or any other corrosive agent. The same
rules apply for orage. Operate the machine in an open, or well-ventilated area.
Operating temperature:
Use between -10 and +40°C (+14 and +104°F).
Storage between -20 and +55°C (-4 and 131°F).
Air humidity:
Lower or equal to 50% at 40°C (104°F).
Lower or equal to 90% at 20°C (68°F).
Altitude:
Up to 1000 meters above sea level (3280 feet).
PROTECTION OF THE INDIVIDUALS
Resistance welding can be dangerous and cause serious injuries or even death. It needs to be used by a qualied technician with
training relevant to the machine.
Welding exposes the user to dangerous heat, arc rays, electromagnetic elds, risk of electric shock, noise and gas fumes. People
wearing pacemakers are advised to consult a doctor before using the welding machine.
To protect oneself as well as the other, ensure the following safety precautions are taken:
In order to protect you from burns and radiations, wear clothing without turn-up or cus. These clothes must be
insulating, dry, reproof, in good condition and cover the whole body.
Wear protective gloves which guarantee electrical and thermal insulation.
Use sucient welding protective gear for the whole body: hood, gloves, jacket, trousers... (varies depending on the
application/operation). Protect the eyes during cleaning operations. Contact lenses are prohibited during use.
It may be necessary to install reproof welding curtains to protect others against arc rays, weld spatters and sparks. .
Ask people around the working area to look away from at the arc or the molten metal, and to wear protective clothing.
Ensure ear protection is worn by the operator if the work exceeds the authorised noise limit (the same applies to any
person in the welding area).
Parts that have previously been welded will be hot and may cause burns if manipulated. During maintenance work
on the torch or the electrode holder, you should make sure it’s cold enough and wait at least 10 minutes before any
intervention. When using a water-cooled torch, make sure that the cooling unit is switched on to avoid any burns
caused by the liquid.
It is important to secure the working area before leaving to ensure the protection of property and the safety of others.
WELDING FUMES AND GAS
Fumes, gas and dust produced during welding are hazardous to health. It is mandatory to ensure adequate
ventilation and/or extraction to keep fumes and gas away from the work area. Using an air fed welding helmet is
recommended in case of insucient ventilation in the workplace.
Check that the air supply is eective by referring to the recommended safety regulations.
10
SPOT 2600 / 2700 / 3900 - 230 V
3900 - 400 V / PRO 230 V/ PRO 400 V
EN
Translation of the original instructions

Похожие устройства

Скачать