Metabo KFM 15-10 F 601752500 Инструкция к товару онлайн [17/124] 817575

ENGLISH en

KFMPB 15-10 F (see page 3, Fig. B):

Switching on: slide the paddle switch (22) in the

direction of the arrow and then press the

paddle switch (22).

Switching off: release the paddle switch (22).

KFM 16-15 F

(see page 3, Fig. B):

Torque activation:

Switching on: press in the lock (23) and then press

the trigger switch (24). Release the lock (23).

Switching off: release the trigger switch (24).

Continuous operation:

Switching on: press in the lock (23) and hold it in

place. Press and hold in the trigger switch

(24). The machine is now switched on. Now

press in the lock (23) once more to lock the

trigger (24) (continuous operation).

Switching off: press the trigger switch (24) and

release.

8.2 Working Directions (KFM 15-10 F)

The speed can be preset via the thumb-wheel (6)

and is infinitely variable.

Positions 1-6 correspond approximately to the

following no-load speeds:

1.........7800 / min 4 .......10200 / min

2.........8600 / min 5 .......11100 / min

3.........9400 / min 6 .......12200 / min

The VTC electronics make material-compatible

work possible and an almost constant speed, even

under load.

Speed recommendations for different materials:

Aluminium, copper, brass ..............................4-6

Steel up to 400 N/mm2 ..................................4-6

Steel up to 600 N/mm2 ..................................3-5

Steel up to 900 N/mm2 ..................................2-4

Stainless steel................................................1-3

8. The best way to determine the ideal setting is

through a practical trial.

8.3 Working on the outer edge of pipes

1. Determine the diameter of the pipe to be worked

on.

2. See page 3, Fig. C: attach the guide roller (25) to

the guide rail (14) as shown. Move the guide

roller (25) and adjust on the scale (26) on the

pipe diameter. Tighten the guide roller nut with a

spanner and thus tighten the guide roller.

3. Pay attention to the general working instructions

(chapter 8.2).

4. Always hold the machine with both hands on the

designated handles, take a secure stance and

concentrate on the work.

5. Place the machine with the guide roller (25) on

the outer surface of the pipe. Then place the

guide rail on the surface of the pipe end.

6. The indexable inserts (19) do not yet touch the

workpiece. First switch on, then slowly tilt the

machine around the guide roller (25) to move the

milling head close to the workpiece.

7. Pay attention to the general working instructions

(chapter 8.2).

8.4 KFM 16-15 F: Possibility for rotating the

guide rail (14)

The guide rail (14) of the KFM 16-15 is installed

transversely. This permits better absorption of high

forces and permits low-fatigue working for most

tasks.

If you prefer to install the guide rail (14) in a

longitudinal manner, the Metabo customer service

will provide you with conversion instructions on

request.

9.1 Changing indexable inserts

Pull the plug out of the socket before making

any adjustments, changing tools, carrying out

maintenance or cleaning.

Indexable inserts, holders for indexable

inserts, the workpiece and chips can be hot

after work. Wear protective gloves.

Regularly check the indexable insert holder (18).

Repair/replace damaged or worn holders for the

indexable inserts.

Regularly check all indexable inserts (19). Change

damaged or worn indexable inserts.

Turn/replace blunt indexable inserts or inserts

where the coating is worn in due time. Blunt

indexable inserts increase the risk that the machine

will catch and breaks loose or that the indexable

insert plate holder (18) is damaged.

Do not use heavily worn or defective indexable

insert plates.

Always turn or replace all indexable inserts.

Use only indexable inserts approved by

Metabo. See the Accessories Section.

Figure A: Normal wear: turn / replace indexable

insert.

Figure B: Wear after working on hard materials: turn

/ replace turning plate. In the event of heavier wear,

do not use the indexable insert plate and instead

replace.

1. Loosen the screws (12) and slide one chip

protection plate (13) upwards.

2. Turn the indexable insert holder (18) manually if

necessary.

3. Unscrew the fastening screw (20) and remove

the indexable insert (19).

4. Clean indexable insert (19) and clamping

surfaces on the indexable insert holder (18).

5. Turn the indexable insert or, if all blades are

blunt, replace the indexable inserts.

6. Fix again the indexable insert (19) with a

fastening screw (20). Torque: 3.5 Nm.

9. Maintenance

Metabo KFM 15-10 F 601752500 Инструкция к товару онлайн [17/124] 817575

Похожие устройства