Home
Главная
Karcher
Аккумуляторные
HT 650/36 Bp 1.042-506.0
Инструкция к Karcher HT 650/36 Bp 1.042-506.0 Страница: 16

Karcher HT 650/36 Bp 1.042-506.0 Инструкция к Karcher HT 650/36 Bp 1.042-506.0 онлайн [16/200] 818370

16 English

몇 CAUTION

Risk of injury from sharp blades

Wear safety goggles and protective gloves when work-

ing on the device.

Cleaning the device

ATTENTION

Incorrect cleaning

Damage to the device

Clean the device with a damp cloth.

Do not use solvent-based cleaning agents.

Do not immerse the device in water.

Do not clean the device with a hose or high-pressure

water jet.

Illustration J

1. Allow the device to cool down.

2. Remove plant residue and dirt from the blade and

motor casing with a brush.

3. Clean the ventilation slits on the device with a brush.

Checking the blade screw connection

몇 CAUTION

Loose screw connections

Incision injuries through uncontrolled blade movements

Check the screw connection of the blade regularly to en-

sure it is firmly fastened.

Illustration K

1. Check that all screws/nuts are tight.

2. Tighten any loose screws/nuts.

Oiling the blade sections

In order to maintain the blade quality, the blade sections

should be oiled after each use.

Note

Using thin machine oil or spray oil will yield very good

results.

Illustration L

1. Place the device on a flat surface.

2. Apply oil to the top of the blade sections.

Sharpening the blade sections

Note

Remove as little material as possible during sharpening

and maintain the original angle of the blade tooth in the

process.

몇 CAUTION

Sharp blade

Incision injuries

Wear suitable protective gloves when sharpening the

blade sections.

1. Clamp the blade in a vice.

2. Sharpen the exposed side of the blade teeth with a

file.

3. Carefully push the blade further by hand so that the

unsharpened blade teeth are accessible.

4. Sharpen the exposed side of all blade teeth with a

file.

Lubrication

Note

Observe the lubrication interval specified on the device

to increase the service life of the device and to prevent

premature defects.

1. Remove the Phillips head screw.

Illustration M

2. Press the transmission grease into the opening with

a grease gun.

3. If necessary, remove the excess transmission

grease.

4. Tighten the Phillips head screw.

Troubleshooting guide

Malfunctions often have simple causes that you can

remedy yourself using the following overview. When in

doubt, or in the case of malfunctions not mentioned

here, please contact your authorised Customer Service.

As the battery pack ages, even if it is looked after, its ca-

pacity reduces such that the full run time will no longer

be reached when fully charged. This does not indicate a

defect.

Warranty

The warranty conditions issued by our relevant sales

company apply in all countries. We shall remedy possi-

ble malfunctions on your appliance within the warranty

period free of cost, provided that a material or manufac-

turing defect is the cause. In a warranty case, please

contact your dealer (with the purchase receipt) or the

next authorised customer service site.

(See overleaf for the address)

Technical data

Fault Cause Rectification

The device does not start

Battery pack is not inserted correctly.  Push the battery pack into the mounting

until it latches into place.

Battery pack is empty  Charge the battery pack.

Battery pack is defective.  Replace the battery pack.

The device stops during

operation

Blade blocked with cutting material.  Remove cutting material from the blade.

The battery has overheated  Stop working and allow the battery to cool

down to normal battery temperature.

Motor has overheated  Stop working and allow the motor to cool

down.

HT 650/

36 Bp

Device performance data

Working voltage of the battery V 36

Idling speed (setting high) /min 3200

Idling speed (setting low) /min 2800

Cut material diameter (max.) mm 33

Karcher HT 650/36 Bp 1.042-506.0 Инструкция к Karcher HT 650/36 Bp 1.042-506.0 онлайн [16/200] 818370

Похожие устройства