P.I.T. 750Вт, 110мм, 1000-3100 ход/мин, 3 режима PST110-C Инструкция к товару онлайн [9/25] 819571

Jig Saw

um.

During prolonged periods of use at a low

stroke rate, the power tool may heat up sig-

niﬁ cantly. Remove the saw blade and let the

power tool run at the maximum stroke rate for

around three minutes to cool down.

Working Advice

► Pull the plug out of the socket before

carrying out any work on the power

tool.

► Switch the power tool oﬀ immediately if

the saw blade becomes blocked.

► When machining small or thin work-

pieces, always use a stable base or saw

table.

Before sawing into wood, chipboard, building

materials, etc., check for and remove any for-

eign objects such as nails, screws, etc.

Plunge cutting (see ﬁ gure G)

► Plunge cuts may only be applied to

soft materials, such as wood, gypsum

board, etc.

For plunge cutting, use only short saw blades.

Plunge cutting is possible only with a mitre

angle of 0°.

Place the power tool so that the front edge of

the base plate rests on the workpiece, with-

out the saw blade touching the workpiece,

and switch it on. On power tools with stroke

rate control, select the maximum stroke rate.

Press the power tool ﬁ rmly against the work-

piece and allow the saw blade to plunge slow-

ly into the workpiece.

As soon as the base plate rests fully on the

workpiece, continue sawing along the re-

quired cutting line.

Parallel guide

When working with the parallel guide, the

workpiece must be no more than 30 mm thick.

Parallel cuts: Loosen the locking screw and

slide the scale on the parallel guide through

the guide in the base plate. Adjust the desired

cutting width as a scale value on the inside

edge of the base plate. Retighten the locking

screw.

The parallel guide can also be used in combi-

nation with the guide rail.

Coolant/lubricant

As the material heats up along the cutting line

when cutting metal, you should apply coolant

or lubricant.

Maintenance and Service

Maintenance and Cleaning

► Pull the plug out of the socket before

carrying out any work on the power

tool.

► To ensure safe and eﬃ cient operation,

always keep the power tool and the

ventilation slots clean.

In order to avoid safety hazards, if the power

supply cord needs to be replaced, this must

be done by P. I. T. or by an after-sales service

centre that is authorised to repair P.I.T. power

tools.

Clean the saw blade receptacle regularly. For

this, remove the saw blade from the power

tool and lightly tap out the power tool on a lev-

el surface.

If the power tool becomes very dirty, this can

lead to serious faults. For this reason, do not

cut materials which generate large quantities

of dust from below or overhead.

► In extreme conditions, always use a

dust extractor if possible.

Blow out venti-

lation slots frequently and install a residual

current device (RCD) upstream. When ma-

chining metals, conductive dust can settle

inside the power tool, which can aﬀ ect its

protective insulation.

If the dust outlet is clogged, turn oﬀ the power

tool and remove dust and swarf.

Lubricate the idler roller with a drop of oil from

time to time.

Check the guide roller regularly. The worn

roller must be replaced by an authorized

P.I.T.power tool workshop.

Service

►

Repairing your power tool commission

only qualiﬁ ed personnel and only with the

use of original spare parts. This ensures

the safety of the power tool.

The list of authorized service centers can be

viewed on the oﬃ cial website of P.I.T. by the

link: https://pittools.ru/servises/

Storage and transportation

Store the instrument in closed rooms with

natural ventilation in a package at an air

temperature from 0 ° C to + 50 ° C and an air

humidity of no more than 80%.

Products can be transported by any type of

closed transport in the manufacturer’s pack-

aging or without it, while preserving the prod-

uct from mechanical damage, atmospheric

precipitation. Remove the exchange tool from

the power tool before transporting it.

P.I.T. 750Вт, 110мм, 1000-3100 ход/мин, 3 режима PST110-C Инструкция к товару онлайн [9/25] 819571

Похожие устройства