Ryobi ONE+ R18MT-0 без аккумулятора в комплекте 5133002466 Инструкция к товару онлайн [5/144] 822150

SHUVRQDOLQMXU\

Ŷ When making a plunge cut into soft materials like wood

and plasterboard using the cutting accessory, gradually

bring the vibrating blade to the workpiece. Do not push

the vibrating blade hard into the material to be cut. Let

the product do the work and concentrate on keeping the

product and the cutting accessory stable in the position

you wish to make the cut.

Ŷ 8VHWKHGHSWKKHLJKWJDXJHWRKHOSVHW\RXUGHSWKRI

cut or prevent cutting too deeply into the material.

Ŷ Take extra care when cutting in non-ferrous metals.

The vibrating cutting blade may skip around before

beginning the cut. If necessary, drill some holes along

the line to be cut before you start cutting.

Ŷ ,I WKH FXWWLQJ DFFHVVRULHV EHFRPH MDPPHG LQ WKH

workpiece, switch off the product and disconnect from

the power supply. If the cutting accessory cannot

be removed easily, allow the cutting accessory to

adequately cool before releasing the cutting accessory

from the product. Wear gloves and use hand tools, such

as pliers or wrench, to remove the cutting accessory

from the workpiece.

OVERCURRENT PROTECTION

When overcurrent is detected, the product will automatically

switch off.

If the product stops working, release the trigger and then

apply again. The product should again start working.

MAINTENANCE

WARNING

The product should never be connected to a power

VXSSO\ ZKHQ DVVHPEOLQJ SDUWV PDNLQJ DGMXVWPHQWV

cleaning, performing maintenance, or when the product

is not in use. Disconnecting the product from the power

supply will prevent accidental starting that could cause

VHULRXVLQMXU\

WARNING

When servicing, use only original manufacturer’s

replacement parts, accessories and attachments. Use of

any other parts may create a hazard or cause product

damage.

Ŷ Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to various types of commercial

solvents and may be damaged by their use. Use clean

cloths to remove dirt, carbon dust, etc.

WARNING

'RQRWDWDQ\WLPHOHWEUDNHÀXLGVJDVROLQHSHWUROHXP

based products, penetrating oils, etc., come in contact

with plastic parts. Chemicals can damage, weaken or

destroy plastic which may result in serious personal

LQMXU\

WARNING

For greater safety and reliability, all repairs should be

performed by an authorised service centre.

The dust from plaster and wall board is abrasive and may

cause premature failure of the product if it is allowed to

enter the motor area. Thoroughly clean the product after

use by using a brush and a vacuum. Take care not to

push dirt into the ventilation openings. Beware of using

compressed air to clean the product because dust and grit

FDQFDXVHVHULRXVH\HLQMXU\

LUBRICATION

All of the bearings in the product are lubricated with a

VXI¿FLHQWDPRXQWRIKLJKJUDGHOXEULFDQWIRUWKHOLIHVSDQRI

the product under normal operating conditions. Therefore,

no further lubrication is required.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing

of as waste. The machine, accessories and

packaging should be sorted for environment-

friendly recycling.

SYMBOLS ON THE PRODUCT

Safety alert

CE conformity

No-load speed

V Volts

Direct current

EurAsian Conformity Mark

Please read the instructions carefully before

starting the machine.

Ukrainian mark of conformity

3 English |

Ryobi ONE+ R18MT-0 без аккумулятора в комплекте 5133002466 Инструкция к товару онлайн [5/144] 822150

Похожие устройства