Home
Главная
Bort
Электрические
KEX-3500 91278166
Инструкция по эксплуатации Страница: 9

Bort KEX-3500 91278166 Инструкция по эксплуатации онлайн [9/32] 822812

aging of cable.

2. Broken switch.

3. Smoke or stench of scorched insulation.

Before starting:

• Before starting the cleaner, make sure that it is receiv-

ing water correctly. Operating the cleaner without wa-

ter could damage the seals.

• Before using the cleaner, CHECK every time that the

screws are fully tightened and that there are no broken

or worn parts.

Specic safety rules

• Do not disconnect the plug by pulling on the electrical

cable.

• If you are too far from the object you wish to clean, do

not move the cleaner nearer by pulling on the high

pressure hose; use the handle provided.

• In versions not equipped with TSS device, do not oper-

ate the cleaner for more than 1-2 minutes with the gun

closed as this could damage the seals.

• Protect the cleaner from freezing during the winter.

• Do not obstruct the ventilation grilles during opera-

tion.

• The cross-section of any extension cables used must

be proportional to their length, i.e. the longer the

extension cable, the greater the cross-section; cables

with a protection level of “IPX5” must be used.

• Position the cleaner AS NEAR POSSIBLE to the water

supply.

• The packaging is easily recyclable, and must be dis-

posed of in compliance with the regulations in force in

the country of installation.

• Use the cleaner only with accessories and replacement

parts authorized by the manufacturer. The use of origi-

nal accessories and replacement parts will ensure safe,

trouble-free operation.

• The cleaner must be used standing on a secure, stable

surface.

• Avoid unintentional ring of the trigger. Do not carry

the lance/ trigger assembly with your hand over the

trigger. Always use the trigger lock mechanism.

• Ensure that the safety lock on the trigger is used, when

you have stopped using the pressure washer to pre-

vent accidental operation.

• DO NOT use the cleaner with inammable or toxic liq-

uids, or any products which are not compatible with

the correct operation of the cleaner.

• DO NOT direct the water jet towards people or animals.

• DO NOT direct the water jet towards the unit itself,

electrical parts or towards other electrical equipment.

• DO NOT use the cleaner outdoors in case of rain.

• DO NOT allow children or incompetent persons to use

the cleaner.

• DO NOT touch the plug and/or socket with wet hands.

• DO NOT use the cleaner if the electrical cable is dam-

aged.

• DO NOT use the cleaner if the high pressure hose is

damaged.

• DO NOT jam the trigger in the operating position.

• Check that the data plates are axed to the cleaner, if

not, inform your dealer. Cleaners without plates must

NOT be used as they are unidentiable and potentially

dangerous.

• DO NOT tamper with or alter the calibration of the safe-

ty valve.

• DO NOT alter the original diameter of the spray head

nozzle.

• DO NOT leave the cleaner unattended.

• DO NOT move the cleaner by pulling on the electrical

cable.

• All electrical conductors MUST BE PROTECTED against

the water jet.

• Use a Residual Current Device (RCD) of not more than

30 mA, at the plug socket when using this appliance.

• The high pressure may cause materials to bounce o

surfaces at speed; therefore protective clothing and

safety goggles MUST BE WORN.

• Before doing work on the cleaner, REMOVE the plug.

• Before pressing the trigger, GRIP the gun rmly to

counteract the recoil.

• COMPLY WITH the requirements of the local water sup-

ply company. According to DIN 1988, power-jet clean-

ers may only be connected to the mains drinking water

supply if a backow preventer valve with drain facility

is installed in the supply hose.

• Maintenance and/or repair of electrical components

MUST be carried out by qualied sta.

• DISCHARGE residual pressure before disconnecting

the cleaner hose.

ASSEMBLY

High pressure washer comes assembled and ready for

use.

Connection:

1. Attach the high pressure hose to the pressure water

outlet of the machine.

2. Attach the spray handle to the high pressure hose. Pri-

or to operating the machine please ensure that the high

pressure hose has been completely uncoiled. Whilst the

machine is in operation the hose MUST not loop.

3. Mount the nozzle or any other equipment you want

to use.

4. Connect the machine to the water and power sup-

plies.

PRE-OPERATION

Adjusting fan pattern

(g. 2)

Water can be sprayed with a narrow stream or fanlike.

The kit includes 4 nozzles with an unregulated spray an-

gle of 0

, 15

, 25

, 40

. Install the required nozzle before

Bort KEX-3500 91278166 Инструкция по эксплуатации онлайн [9/32] 822812

Похожие устройства