Hikoki CC14ST CC14STNTZ Инструкция к товару онлайн [10/32] 823196
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Hikoki CC14ST CC14STNTZ Инструкция к товару онлайн [10/32] 823196

Hikoki CC14ST CC14STNTZ Инструкция к товару онлайн [10/32] 823196
English
10
Information concerning airborne noise and vibration
The measured values were determined according to
EN62841.
ThetypicalA-weightedsoundpressurelevel:95dB(A).
ThetypicalA-weighiedsoundpowerlevel:108dB(A).
Wearhearingprotection.
● Information about power supply system of nominal
voltage 230 V~
Under unfavorable mains conditions, this power tool
may cause transient voltage drops or interfering voltage
uctuations.
This power tool is intended for theconnectiontoapower
supply system with a maximum permissible system
impedanceZ
MAXof0.14Ohmattheinterfacepoint(power
servicebox)oftheuser’ssupply.
The user has to ensure that this power tool is connected
onlytoapowersupplysystemwhichfulllstherequirement
above.
If necessary, the user can ask the public power supply
companyforthesystemimpedanceattheinterfacepoint.
● Information about power supply system of nominal
voltage 230 V~
This tool should be used only if it is connected to a 16 A
Fusewithgldisconnectioncharacteristic.
MAINTENANCE AND INSPECTION
CAUTION
Be sure to switch o and pull o the plug from the power
outletbeforeinspectionandmaintenance.
1. Replacing a cut-o wheel
Whenthe cut-o wheelhas already becomedull while
continuallyusing,theunnecessary load isgotfrom the
motor. Consequently, redress or replace a dull cut-o
wheeltoensuregrindingeciency.
2. Inspecting the carbon brushes (Fig. 14)
The Motor employs carbon brushes which are
consumable parts. Since an excessive worn carbon
brush can result in motor trouble, replace both carbon
brushes with new ones shown in the gure when it
becomes worn to or near the "wear limit". In addition,
alwayskeepcarbonbrushescleanandensurethatthey
slidefreelywithinthebrushholders.
3. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
theyareproperlytightened.Shouldanyofthescrewsbe
loose,retightenthemimmediately.Failuretodosocould
resultinserioushazard.
4. Replacing supply cord
Ifthereplacementofthesupplycordisnecessary,ithas
tobedonebyHiKOKIAuthorizedServiceCentertoavoid
asafetyhazard.
5. Lubrication
Supplyoilinthefollowingoilsupplypointsonceamonth
soastokeepthemachineworkableforalongtime.
Oilsupplypoints.
○ Rotarypartofshaft
○ Rotarypartofvise
○ Slidewayofvise(A)
6. Cleaning
Wipeochipandwasteadheredtothemachinewitha
clothortheliketimetotime.Becarefulnottomakethe
motorportionwetwithoilorwater.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
countrymustbeobserved.
GUARANTEE
We guarantee HiKOKI Power Tools in accordance with
statutory/country specic regulation. This guarantee does
notcoverdefectsordamageduetomisuse,abuse,ornormal
wearandtear.Incaseofcomplaint,pleasesendthePower
Tool, undismantled, with the GUARANTEE CERTIFICATE
found at the end of this Handling instruction, to a HiKOKI
AuthorizedServiceCenter.
NOTE
Due to HiKOKI’s continuing program of research and
development, the specications herein are subject to
changewithoutpriornotice.
000Book_CC14ST_TurUkRu.indb 10 2019/02/21 16:23:14

Похожие устройства

Скачать