General Climate GC-CF36HRN2/GU-U36HN2 комплект GCCF36HRN2 Инструкция пульт ДУ онлайн [5/10] 825393
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

General Climate GC-CF36HRN2/GU-U36HN2 комплект GCCF36HRN2 Инструкция пульт ДУ онлайн [5/10] 825393

General Climate GC-CF18HRN2/GU-U18HN2 комплект GCCF18HRN2 Инструкция пульт ДУ онлайн [5/10] 825391
4 5
3. Функции кнопок
1.
ON/OFF
Включение и выключение кондиционера.
2.
MODE
Тепловой режим работы кондиционера, каждое нажатие кноп-
ки выбирает режим:
АВТО
->
ОХЛАЖДЕНИЕ
->
ОСУШКА
->
НАГРЕВ
->
ВЕНТИЛЯТОР
3
. FAN
Выбор скорости вентилятора внутреннего блока:
АВТО
->
СРЕДНЯЯ
->
ВЫСОКАЯ
4
. SLEEP
Включение/выключение ночного режима, снижение энергопо-
требления и уровня шума во время сна. Режим может быть ак-
тивирован только при ОХЛАЖДЕНИИ, НАГРЕВЕ или АВТО. На-
жатие кнопок MODE, FAN или ON/OFF отключает ночной режим.
5.
TURBO
Включение/выключение функции TURBO, которая в режиме
ОХЛАЖДЕНИЯ позволяет быстро достигнуть заданной темпе-
ратуры.
7.
5 6
Function buttons
1
2
Each time the button is pressed, the operation
mode is selected in a sequence of following:
3
MODE Button
4
5
ON/OFF Button
Operation starts when this button is pressed
and stops when this button is pressed again.
NOTE: Heat mode is for Cooling & Heating models only .
AUTO
COOL
DRY
HEAT FAN
SHORTCUT Button
TIMER ON Button
TIMER OFF Button
Used to restore the current settings or resume previous settings.
On the first time connecting to the power, if push the SHORTCUT button, the unit
O
will operate on AUTO mode, 26 C, and fan speed is Auto.
Push this button when remote controller is on, the system will automatically revert
back to the previous settings including operating mode, setting temperature, fan
speed level and sleep feature(if activated). And transmit the signals to the unit.
If push this button when remote controller is off, the system will only resume the
previous settings and will not transmit the signals to the unit. And the sleep
feature is disable.
If pushing more than 2 seconds, the system will automatically restore the current
operation settings including operating mode, setting temperature, fan speed level
and sleep feature(if activated ).
8
6
7
SWING Button
DIRECT Button
Used to change the louver movement and set the desired up/down air flow direction.
O
The louver changes 6 in angle for each press.
Used to stop or start horizontal louver auto swing feature.
SELF CLEAN Button
UP Button( )
o
Push this button to decrease the indoor temperature setting in 1 C increments
o
to 17 C.
DOWN Button( )
9
11
13
12
14
15
10
Used to select the fan speed in four steps:
AUTO LOW MED HIGH
FAN Button
Press this button to initiate the auto-on time sequence. Each press will increase
the auto-timed setting in 30 minutes increments. When the setting time displays
10.0, each press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-on time to 0.0.
Press this button to initiate the auto-off time sequence. Each press will increase
the auto-timed setting in 30 minutes increments. When the setting time displays
10.0, each press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-off time to 0.0
1
2
4
5
3
9
10
8
6
7
11
12
13
14
15
ON/OFF
MODE
FAN
TEMP
SHORT
CUT
TIME R ON
TIMER OFF
SLEEP FRESH
SWING DIRECT
LED FOL LO W ME
TURBO SEL F CLEAN
Active/Disable Self Clean function
SLEEP Button
FRESH Button
NOTE: While the unit is running under SLEEP
mode, it would be cancelled if MODE, F AN
SPEED or ON/OFF button is pressed.
Active/Disable sleep function. It can maintain
the most comfortable temperature and save
energy. This function is available on COOL,
HEAT or AUTO mode only .
Pushing this button to activate the FRESH
function. Pushing it again to disable.
TURBO Button
Active/Disable Turbo function. Turbo function
enables the unit to reach the preset temperature
in the shortest time. When press this button
on cooling mode, the unit will blow strong
cooling air with super high fan speed. When
press this button on heating mode(applicable
to the unit adopts PTC only), the PTC will be
energized and bring fast heating operation.
LED Button
Disable/Active indoor screen Display. When
pushing the button, the indoor screen display
is cleared, press it again to light the display.
o
Push this button to increase the indoor temperature setting in 1 C increments
o
to 30 C.
FOLLOW ME Button: Push this button to initiate the Follow Me feature, the
remote display is actual temperature at its location. The remote control will send
this signal to the air conditioner every 3 minutes interval until press the Follow Me
button again. The air conditioner will cancel the Follow Me feature automatically
if it does not receive the signal during any 7 minute interval.
(УВЕЛИЧЕНИЕ) Нажатие кнопки увеличивает температуру на 1 °C (до 30 °C).
5 6
Function buttons
1
2
Each time the button is pressed, the operation
mode is selected in a sequence of following:
3
MODE Button
4
5
ON/OFF Button
Operation starts when this button is pressed
and stops when this button is pressed again.
NOTE: Heat mode is for Cooling & Heating models only .
AUTO
COOL
DRY
HEAT FAN
SHORTCUT Button
TIMER ON Button
TIMER OFF Button
Used to restore the current settings or resume previous settings.
On the first time connecting to the power, if push the SHORTCUT button, the unit
O
will operate on AUTO mode, 26 C, and fan speed is Auto.
Push this button when remote controller is on, the system will automatically revert
back to the previous settings including operating mode, setting temperature, fan
speed level and sleep feature(if activated). And transmit the signals to the unit.
If push this button when remote controller is off, the system will only resume the
previous settings and will not transmit the signals to the unit. And the sleep
feature is disable.
If pushing more than 2 seconds, the system will automatically restore the current
operation settings including operating mode, setting temperature, fan speed level
and sleep feature(if activated ).
8
6
7
SWING Button
DIRECT Button
Used to change the louver movement and set the desired up/down air flow direction.
O
The louver changes 6 in angle for each press.
Used to stop or start horizontal louver auto swing feature.
SELF CLEAN Button
UP Button( )
o
Push this button to decrease the indoor temperature setting in 1 C increments
o
to 17 C.
DOWN Button( )
9
11
13
12
14
15
10
Used to select the fan speed in four steps:
AUTO LOW MED HIGH
FAN Button
Press this button to initiate the auto-on time sequence. Each press will increase
the auto-timed setting in 30 minutes increments. When the setting time displays
10.0, each press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-on time to 0.0.
Press this button to initiate the auto-off time sequence. Each press will increase
the auto-timed setting in 30 minutes increments. When the setting time displays
10.0, each press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-off time to 0.0
1
2
4
5
3
9
10
8
6
7
11
12
13
14
15
ON/OFF
MODE
FAN
TEMP
SHORT
CUT
TIME R ON
TIMER OFF
SLEEP FRESH
SWING DIRECT
LED FOL LO W ME
TURBO SEL F CLEAN
Active/Disable Self Clean function
SLEEP Button
FRESH Button
NOTE: While the unit is running under SLEEP
mode, it would be cancelled if MODE, F AN
SPEED or ON/OFF button is pressed.
Active/Disable sleep function. It can maintain
the most comfortable temperature and save
energy. This function is available on COOL,
HEAT or AUTO mode only .
Pushing this button to activate the FRESH
function. Pushing it again to disable.
TURBO Button
Active/Disable Turbo function. Turbo function
enables the unit to reach the preset temperature
in the shortest time. When press this button
on cooling mode, the unit will blow strong
cooling air with super high fan speed. When
press this button on heating mode(applicable
to the unit adopts PTC only), the PTC will be
energized and bring fast heating operation.
LED Button
Disable/Active indoor screen Display. When
pushing the button, the indoor screen display
is cleared, press it again to light the display.
o
Push this button to increase the indoor temperature setting in 1 C increments
o
to 30 C.
FOLLOW ME Button: Push this button to initiate the Follow Me feature, the
remote display is actual temperature at its location. The remote control will send
this signal to the air conditioner every 3 minutes interval until press the Follow Me
button again. The air conditioner will cancel the Follow Me feature automatically
if it does not receive the signal during any 7 minute interval.
(УМЕНЬШЕНИЕ) Нажатие кнопки уменьшает температуру на 1 °C (до 17 °C).
SHORTCUT
• Используется для сохранения и восстановления предпочтительных параметров работы кондиционера.
•
Если нажать и удерживать более 2 сек, то текущие настройки (тепловой режим работы, устанавливаемая
температура, скорость вентилятора, ночной режим) будут сохранены в памяти.
• Если нажать, когда кондиционер включен, то он немедленно начнёт работать с настройками, которые
ранее были сохранены в памяти.
• Если нажать при выключенном кондиционере, то ранее сохранённые настройки восстановятся на пульте,
для передачи их на внутренний блок необходимо включить кондиционер кнопкой ON/OFF.
• Если в памяти ещё не было сохранено никаких настроек, например, первое включение кондиционера,
то нажатие кнопки установит автоматический тепловой режим с температурой 26°C и автоматической
скоростью вентилятора внутреннего блока.
8.
TIMER ON
Установка времени автоматического включения кондиционера. Каждое нажатие увеличивает время на 30
мин, при достижении 10 часов - на 60 мин. Чтобы отменить настройку таймера просто установите время в 0.
10.
9.
TIMER OFF
Установка времени автоматического выключения кондиционера. Каждое нажатие увеличивает это время на 30
мин, при достижении 10 часов - на 60 мин. Чтобы отменить настройку таймера просто установите время в 0.
11.
Используется для настройки направления движения воздуха. Каждое нажатие меняет угол
на 6°.
5 6
Function buttons
1
2
Each time the button is pressed, the operation
mode is selected in a sequence of following:
3
MODE Button
4
5
ON/OFF Button
Operation starts when this button is pressed
and stops when this button is pressed again.
NOTE: Heat mode is for Cooling & Heating models only .
AUTO
COOL
DRY
HEAT FAN
SHORTCUT Button
TIMER ON Button
TIMER OFF Button
Used to restore the current settings or resume previous settings.
On the first time connecting to the power, if push the SHORTCUT button, the unit
O
will operate on AUTO mode, 26 C, and fan speed is Auto.
Push this button when remote controller is on, the system will automatically revert
back to the previous settings including operating mode, setting temperature, fan
speed level and sleep feature(if activated). And transmit the signals to the unit.
If push this button when remote controller is off, the system will only resume the
previous settings and will not transmit the signals to the unit. And the sleep
feature is disable.
If pushing more than 2 seconds, the system will automatically restore the current
operation settings including operating mode, setting temperature, fan speed level
and sleep feature(if activated ).
8
6
7
SWING Button
DIRECT Button
Used to change the louver movement and set the desired up/down air flow direction.
O
The louver changes 6 in angle for each press.
Used to stop or start horizontal louver auto swing feature.
SELF CLEAN Button
UP Button( )
o
Push this button to decrease the indoor temperature setting in 1 C increments
o
to 17 C.
DOWN Button( )
9
11
13
12
14
15
10
Used to select the fan speed in four steps:
AUTO LOW MED HIGH
FAN Button
Press this button to initiate the auto-on time sequence. Each press will increase
the auto-timed setting in 30 minutes increments. When the setting time displays
10.0, each press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-on time to 0.0.
Press this button to initiate the auto-off time sequence. Each press will increase
the auto-timed setting in 30 minutes increments. When the setting time displays
10.0, each press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-off time to 0.0
Active/Disable Self Clean function
SLEEP Button
FRESH Button
NOTE: While the unit is running under SLEEP
mode, it would be cancelled if MODE, F AN
SPEED or ON/OFF button is pressed.
Active/Disable sleep function. It can maintain
the most comfortable temperature and save
energy. This function is available on COOL,
HEAT or AUTO mode only .
Pushing this button to activate the FRESH
function. Pushing it again to disable.
TURBO Button
Active/Disable Turbo function. Turbo function
enables the unit to reach the preset temperature
in the shortest time. When press this button
on cooling mode, the unit will blow strong
cooling air with super high fan speed. When
press this button on heating mode(applicable
to the unit adopts PTC only), the PTC will be
energized and bring fast heating operation.
LED Button
Disable/Active indoor screen Display. When
pushing the button, the indoor screen display
is cleared, press it again to light the display.
o
Push this button to increase the indoor temperature setting in 1 C increments
o
to 30 C.
FOLLOW ME Button: Push this button to initiate the Follow Me feature, the
remote display is actual temperature at its location. The remote control will send
this signal to the air conditioner every 3 minutes interval until press the Follow Me
button again. The air conditioner will cancel the Follow Me feature automatically
if it does not receive the signal during any 7 minute interval.
MODE
FAN
TEMP
ON/OFF
SHORT
CUT
TIMER
ON
TIMER
OFF
1
2
4
3
7
8
6
5
9
10
11
12
SLEE P
TURB O
LED
6.
Используется для включения или выключени
я автоматического покачивания заслонки, удерживая кнопку более
2-х сек. - вкл. или выкл. автоматическое покачивание жалюзи.

Похожие устройства

Скачать