Home
Главная
Bosch
Электрические
AdvancedAquatak 140 0.600.8A7.D00
Инструкция к Bosch AdvancedlAquatak 140 06008A7D00 Страница: 18

Bosch AdvancedAquatak 140 0.600.8A7.D00 Инструкция к Bosch AdvancedlAquatak 140 06008A7D00 онлайн [18/294] 828031

18 | English

Working Advice

General

u Never use a roto nozzle or pencil jet to clean motor

vehicles.

Ensure that the pressure washer is on level ground.

Do not overreach with the high pressure hose or move the

pressure washer by pulling the hose, this could cause the

ma-chine to become unstable and fall over.

Do not kink or drive a motor vehicle over the high pressure

hose. Do not expose the high pressure hose to sharp edges

or corners.

Working advice for cleaning with detergents

u Only use cleaning agents suitable specifically for high

pressure washers.

We recommend that you use detergent sparingly for the sake

of the environment. Observe the recommended dilution on

the detergent label.

Recommended cleaning method

Step 1: Attach the fan nozzle and remove the heavy dirt.

Step 2: Attach the foam bottle and spray on the detergent

sparingly.

Step 3: Rinse off the loosened dirt and detergent with the

fan nozzle.

Note: When cleaning a vertical surface spray off dirt/deter-

gent from the bottom and work in an upwards direction.

Rinse from the top and work downwards.

Use with alternative water sources

This high-pressure washer will self prime and can draw water

from water tanks and natural water sources. It is IMPORT-

ANT that the water is clean and the BOSCH inlet filter is clear

and fitted to the machine.

Open tanks/containers and natural water

sources

Use the Self Priming accessory kit comprising:

– Inlet strainer with non return valve

– 3m reinforced supply hose

– Universal coupling to the pressure washer

This enables the pressure washer to draw water up to 0.5m

above the water level in the source. This may take up to 15

seconds.

Submerge the 3m hose in water to displace the air. Connect

the 3m supply hose to the pressure washer ensuring that

the inlet strainer remains submerged in the water source.

Run the pressure washer with the lance disconnected until a

steady flow of water appears from the high pressure hose.

Stop if this has not been achieved within 25 seconds and

check all the connections. Switch off and connect the lance

and nozzle to operate.

It is important to ensure that all hose and coupling connec-

tions are of good quality, air tight and that all washers are in

good condition and correctly seated in place. Failure to do

so may affect the self priming performance.

Water Tanks with outlet connections

When connecting the pressure washer to a water tank with a

suitable tap outlet, first connect the supply hose (not

provided) to the tank outlet, open the tap to allow the water

to displace all the air in the hose and then connect to the

pressure washer.

Troubleshooting

Problem Possible Cause Corrective Action

Motor refuses to start Plug not connected Connect plug

Mains socket faulty Use another socket

Fuse faulty / blown Replace fuse

Extension cable damaged Try without extension cable

Motor protector has activated Allow to cool for 15 minutes

Frozen Wait for pump/water supply hose/accessory to

thaw

Motor stops Fuse faulty / blown Replace fuse

Wrong mains voltage Check that mains voltage corresponds to specific-

ations on the model tag

Motor protector has activated Allow to cool for 15 minutes

Fuses blow Fuses incorrectly rated Change to a mains supply higher than the pres-

sure washer amp consumption

F 016 L81 693 | (10.01.2019) Bosch Power Tools

Bosch AdvancedAquatak 140 0.600.8A7.D00 Инструкция к Bosch AdvancedlAquatak 140 06008A7D00 онлайн [18/294] 828031

Похожие устройства