Home
Главная
Ryobi
2х тактные
RBC31SESO 5133002540
Инструкция к Ryobi RBC31SESO Страница: 6

Ryobi RBC31SESO 5133002540 Инструкция к Ryobi RBC31SESO онлайн [6/288] 832801

4 | English

■ The product should be held at a comfortable position

with the trigger handle about hip height.

■ Maintain your grip and balance on both feet. Position

yourself so that you will not be drawn off balance by the

kickback reaction of the cutting blade.

■ Adjust the strap hanger to a comfortable position.

■ Exercise extreme caution when using the blade with

the product. Blade thrust is the reaction that may occur

when the spinning blade contacts anything it cannot

cut. This contact may cause the blade to stop for an

instant, and suddenly “thrust” the product away from

the object that was hit. This reaction can be violent

enough to cause the operator to lose control of the

product. Blade thrust may occur without warning if

the blade snags, stalls, or binds. This is more likely to

occur in areas where it is difficult to see the material

being cut. For cutting ease and safety, approach the

weeds being cut from the right to the left. In the event an

unexpected object or woody stock is encountered, this

could minimize the blade thrust reaction.

TRANSPORTATION AND STORAGE

■ Stop the engine and allow it to cool down before storing

or transporting.

■ Clean all foreign materials from the product.

■ If a cutting blade is fitted, cover it with the blade

protector.

■ Drain all fuel from tank into a container approved for

petrol. Remember to properly replace and tighten the

fuel cap.

■ Run the engine until it stops, this will remove all fuel

that could become stale and leave varnish and gum in

the fuel system.

■ Store the product in a cool, dry, and well-ventilated

place that is inaccessible to children. Keep away from

corrosive agents, such as garden chemicals and de-

icing salts. Do not store outdoors.

■ When transporting the product in a vehicle, secure it

against movement or falling to prevent injury to persons

or damage to the product.

■ Never carry or transport the product while the engine

is running.

■ Abide all government and local regulations for the safety

storage and handling of petrol. Excess fuel should be

used in other 2-cycle engine powered equipment.

SHORT TERM

■ Stop the engine, and allow it to cool down before

storing.

■ Clean all foreign material from the product.

■ Store the product in a cool, dry, and well-ventilated

place that is inaccessible to children.

■ Keep away from corrosive agents such as garden

chemicals and de-icing salts.

■ Do not store outdoors.

MAINTENANCE

WARNING

Use only original manufacturer’s replacement parts,

accessories, and attachments. Failure to do so can

cause possible injury, poor performance, and may void

your warranty.

WARNING

The cutting attachment must not rotate in idle mode. If

this requirement is not satisfied, the clutch has to be

adjusted or the product needs an urgent maintenance

by a qualified technician.

WARNING

A leaking fuel cap is a fire hazard and must be replaced

immediately.

WARNING

Note that the blade nut is a nylon nut, which is to be used

for one time assembly only. Do not reuse the nylon nut.

When installing/reinstalling, use a new nylon nut. Failure

to follow this procedure can result in serious injury.

WARNING

Make sure that the nut torque is ≥ 25Nm when

assembling the blade. Failure to follow this procedure

can result in serious injury. (See page 202, step 4)

■ Always stop the engine and allow it to cool down before

making any maintenance.

■ You may make adjustments and repairs described

in this manual. For other repairs, have the product

serviced by an authorised service centre.

■ Consequences of improper maintenance may include

excess carbon deposits resulting in loss of performance

and discharge of black lubricant residue dripping from

the muffler.

■ For replacement line, use only nylon filament line of

the diameter described in the specification table of this

manual.

■ After extending the new cutter line, always return the

product to its normal operation position before starting.

After each use, clean the product with a soft dry cloth.

■ Make sure all guards, straps, deflectors and handles

are properly and securely attached to avoid the risk of

personal injury.

MAINTENANCE SCHEDULE

Check if fastener is fully

tightened

Before each use

Check: Cutting attachment

must not rotate in idle mode ²

Before each use

Check fuel hose Before each use

Ryobi RBC31SESO 5133002540 Инструкция к Ryobi RBC31SESO онлайн [6/288] 832801

Похожие устройства