Home
Главная
Ryobi
Аккумуляторные
MAX POWER RY36CSX35A-160 36В 5133004623
Инструкция к Ryobi RY36CSX35A-0 5133004595 Страница: 7

Ryobi MAX POWER RY36CSX35A-160 36В 5133004623 Инструкция к Ryobi RY36CSX35A-0 5133004595 онлайн [7/328] 835727

English |

with a shield depicting a chainsaw to show compliance

with EN 381-3. (Occasional users may use steel toe-

cap safety boots with protective gaiters which conform

to EN 381-9 if the ground is even and there is little risk

of tripping or catching on undergrowth)

Chainsaw jackets for upper body protection

■ should comply with EN 381-11 and be CE marked

GETTING STARTED

See page 277.

1. Wear full eye protection, ear protection, non-slip

heavy-duty gloves, substantial footwear, and protective

clothing at all times while operating the product. Do not

operate the product when barefoot or wearing open

sandals.

2. Remove the parts from the packaging. Inspect the

product carefully for damage. If any parts are damaged

or missing, contact an authorised service centre.

3. Add chain lubricating oil. Clear the surface around the

oil cap to prevent contamination. Remove the cap from

the oil tank. Pour the oil into the oil tank and monitor

the oil level gauge. Ensure that no dirt enters the oil

tank while filling. Close the oil tank, and tighten the cap.

Wipe away any spillage.

WARNING

Never work without chain lubricant. If the saw chain is

running without lubricant, the guide bar and the saw

chain can be damaged. It is essential to frequently check

the oil level in the oil level gauge and before starting to

use the chainsaw.

NOTE: Ensure that the lubricant ow screw is set to open

for chain and bar oil to be released.

– Turn the screw counterclockwise to open and

increase the oil flow to the chain and bar.

– Turn the screw clockwise to decrease the oil flow to

the chain and bar.

A properly functioning chain and bar lubricating system will

normally discharge oil from the chain during use. To check

the functionality of the chain and bar lubricating system,

point the tip of the chain at a light coloured surface, such

as a newspaper. A distinct line of oil splatter should be

observed after a short time.

4. Remove the guide bar cover.

5. Adjust the chain tension. Turn the chain tensioner

knob counterclockwise to unlock the chain tensioner

adjustment ring. Check the chain tension frequently

while adjusting the tension.

– To increase the chain tension, turn the chain

tensioner adjustment ring clockwise.

– To reduce the chain tension, turn the chain

tensioner adjustment ring counterclockwise.

NOTE: The chain tension is correct when the gap

between the cutter in the chain and the bar is between

3-4 mm. Pull the chain in the middle of the lower side of

the bar downwards (away from the bar), and measure

the distance between the bar and the chain cutters.

NOTE: The temperature of the chain increases during

normal operation causing the chain to stretch. Check

the chain tension frequently and adjust as required.

A chain tensioned while warm may be too tight upon

cooling. Make sure that the chain tension is correctly

adjusted as specified in these instructions.

6. Tighten the chain tensioner knob by turning it clockwise.

7. Align the raised ribs on the battery pack with the

grooves in the product’s battery port. Make sure that

the latch of the battery pack snaps in place and that

the battery pack is fully seated and securely attached

before beginning operation.

WARNING

Always hold the product with your right hand on the rear

handle and your left hand on the front handle.

WARNING

Grip both handles with the thumbs and ngers encircling

the handles. Ensure that your left hand is holding the

front handle so that your thumb is underneath.

8. Start the product. Set the chain brake into the run

position by grasping the top of the chain brake lever/

hand guard and pulling towards the front handle until

you hear a click. Pull the trigger release. Press the

throttle trigger.

NOTE: To stop the product, engage the chain brake by

rotating your left hand around the front handle. Allow the

back of your hand to push the chain brake lever/hand guard

toward the bar while the chain is rotating rapidly. Push the

trigger release and release the throttle trigger.

INSTRUCTIONS CONCERNING THE PROPER

TECHNIQUES FOR BASIC FELLING, LIMBING, AND

CROSS-CUTTING

Understanding the forces within the wood

When you understand the directional pressures and

stresses inside the wood you can reduce the “pinches” or

at least expect them during your cutting. Tension in the

wood means the bers are being pulled apart and if you cut

in this area, the “kerf” or cut will tend to open as the saw

goes through. If a log is being supported on a saw horse

and the end is hanging unsupported over the end then

tension is created on the upper surface due to the weight

of the overhanging log stretching the bers. Likewise, the

underside of the log will be in compression and the bers

are being pushed together. If a cut is made in this area, the

kerf will have the tendency to close up during the cut. This

would pinch the blade.

Push and pull

The reaction force is always opposite to the direction the

chain is moving. Thus, the operator must be ready to

control the tendency for the product to pull away (forward

motion) when cutting on the bottom edge of the bar and the

push backwards (towards the operator) when cutting along

the top edge.

Ryobi MAX POWER RY36CSX35A-160 36В 5133004623 Инструкция к Ryobi RY36CSX35A-0 5133004595 онлайн [7/328] 835727

Похожие устройства