Home
Главная
Ryobi
Аккумуляторные
MAX POWER RY36CSX40B-160 36В 5133004899
Инструкция к Ryobi MAX POWER RY36CSX40B-0 5133004898 Страница: 7

Ryobi MAX POWER RY36CSX40B-160 36В 5133004899 Инструкция к Ryobi MAX POWER RY36CSX40B-0 5133004898 онлайн [7/268] 835733

REMOVING BUTTRESS ROOTS

A buttress root is a large root extending from the trunk of

the tree above the ground. Remove large buttress roots

before felling. Make the horizontal cut into the buttress ﬁ rst,

followed by the vertical cut. Remove the resulting loose

section from the work area. Follow the correct tree felling

procedure after removing the large buttress roots.

BUCKING A LOG

Bucking is cutting a log into lengths. It is important to

make sure your footing is ﬁ rm and your weight is evenly

distributed on both feet. When possible, the log should be

raised and supported by the use of limbs, logs or chocks.

Follow the simple directions for easy cutting. When the log

is supported along its entire length, it is cut from the top

(overbuck).

When the log is supported on one end, cut 1/3 the diameter

from the underside (underbuck). Then make the ﬁ nished

cut by overbucking to meet the ﬁ rst cut.

1/3

2/3

When the log is supported on both ends, cut 1/3 the

diameter from the top (overbuck). Then make the ﬁ nished

cut by underbucking the lower 2/3 to meet the ﬁ rst cut.

2/3

1/3

When bucking on a slope always stand on the uphill side of

the log. To maintain control when “cutting through”, release

the cutting pressure near the end of the cut without relaxing

your grip on the chainsaw handles. Don’t let the chain

contact the ground. After completing the cut, wait for the

saw chain to stop before you move the chainsaw. Always

stop the motor before moving from tree to tree.

LIMBING A TREE

Limbing is removing the branches from a fallen tree. When

limbing, leave larger lower limbs to support the log oﬀ the

ground. Remove the small limbs in one cut. Branches

under tension should be cut from the bottom up to avoid

binding the chainsaw.

SPRINGPOLES

A springpole is any log, branch, rooted stump, or sapling

that is bent under tension by other wood so that it springs

back if the wood holding it is cut or removed.

On a fallen tree, a rooted stump has a high potential of

springing back to the upright position during the bucking

cut to separate the log from the stump. Watch out for

springpoles—they are dangerous. Do not attempt to cut

bent branches or stumps that are under tension unless you

are professionally trained and competent to do so.

WARNING! Springpoles are dangerous and could strike

the operator, causing the operator to lose control of the

chainsaw. This could result in a severe or fatal injury to the

operator. Cutting spring poles should be done by trained

users.

TRANSPORTATION AND STORAGE

■ Turn off the product, remove the battery pack, and allow

the product to cool down before storing or transporting.

■ Remove all foreign materials from the product. Store

the product in a cool, dry, and well-ventilated place that

is inaccessible to children. Keep the product away from

corrosive agents, such as garden chemicals and de-

icing salts. Do not store the product outdoors.

■ Fit the guide bar cover before storing the product or

during transportation.

■ For transportation, secure the product against

movement or falling to prevent injury to persons or

damage to the product.

7 English |

Ryobi MAX POWER RY36CSX40B-160 36В 5133004899 Инструкция к Ryobi MAX POWER RY36CSX40B-0 5133004898 онлайн [7/268] 835733

Похожие устройства