Ryobi ONE+ R18PD3-0 без аккумулятора в комплекте 5133002888 Инструкция к товару онлайн [3/122] 853238

1 English |

Safety, performance, and dependability have been given

top priority in the design of your percussion drill.

INTENDED USE

The percussion drill is intended to be used only by adults

who have read and understood the instructions and

warnings in this manual, and can be considered responsible

for their actions.

The percussion drill is intended to be used in drilling into

various materials, including wood, metal, and plastic using

a drill bit having a shank diameter of less than 13 mm.

When in impact mode, the percussion drill can be used in

drilling masonry and similar materials. When in screwdriving

mode, the percussion drill can be used in driving screws.

Do not use the product in any way other than those stated

for intended use.

WARNING

Read all safety warnings and all instructions. Failure

to follow the warnings and instructions may result in

electric shock, ﬁ re and/or serious injury.

Save all warnings and instruction for future reference.

PERCUSSION DRILL SAFETY WARNINGS

■ Wear ear protectors when impact drilling. Exposure

to noise can cause hearing loss.

■ Use auxiliary handle(s), if supplied with the tool.

Loss of control can cause personal injury.

■ Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring. Cutting

accessory contacting a “live” wire may make exposed

metal parts of the power tool “live” and could give the

operator an electric shock.

■ Hold power tool by insulated gripping surfaces,

when performing an operation where the fastener

may contact hidden wiring. Fasteners contacting a

“live” wire may make exposed metal parts of the power

tool “live” and could give the operator an electric shock.

■ Do not operate on materials (e.g., asbestos) that

present a health hazard.

■ Switch off the product immediately if the bit stalls. Do

not switch on the product again while the bit is stalled,

as doing so could trigger a sudden recoil with a high

reactive force. Determine why the bit stalled and rectify

this, paying heed to the safety instructions.

The possible causes may be:

– it is tilted in the workpiece

– it has pierced the workpiece

– the product is overloaded

■ Sawdust and splinters must not be removed while the

product is running.

■ When working in walls, ceilings, or floors, avoid hitting

electrical cables and gas or water pipes.

■ Secure your workpiece with a clamping device.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national

provisions and regulations.

Follow all special requirements on packaging and labelling

when transporting batteries by a third party. Ensure that

no batteries can come in contact with other batteries

or conductive materials while in transport by protecting

exposed connectors with insulating, non-conductive caps

or tape. Do not transport batteries that are cracked or

leaking. Check with the forwarding company for further

advice.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still

impossible to completely eliminate certain residual risk

factors. The operator should pay particular and additional

attention to these points in order to reduce the risk of

serious personal injury.

■ Injury to hearing - Wear suitable ear protection and limit

exposure.

■ Injury to sight - Wear protective eye shields or goggles

when using the product.

■ Injury caused by vibration - Limit exposure and follow

the instructions on risk reduction in this manual.

■ Electric shock after contact with hidden wires - Hold the

product only by insulated surfaces.

■ Respiratory injury from dust created by operating the

product - Wear suitable protection depending on type

of dust.

RISK REDUCTION

It has been reported that vibrations from handheld tools

may contribute to a condition called Raynaud’s Syndrome

in certain individuals. Symptoms may include tingling,

numbness and blanching of the ﬁ ngers, usually apparent

upon exposure to cold. Hereditary factors, exposure to

cold and dampness, diet, smoking and work practices

are all thought to contribute to the development of these

symptoms. There are measures that can be taken by the

operator to possibly reduce the effects of vibration:

■ Keep your body warm in cold weather. When operating

the unit wear gloves to keep the hands and wrists

warm. It is reported that cold weather is a major factor

contributing to Raynaud’s Syndrome.

■ After each period of operation, exercise to increase

blood circulation.

■ Take frequent work breaks. Limit the amount of

exposure per day.

Ryobi ONE+ R18PD3-0 без аккумулятора в комплекте 5133002888 Инструкция к товару онлайн [3/122] 853238

Похожие устройства