Home
Главная
DWT
Циркулярные (дисковые)
HKS12-54 5.1.17
Инструкция по эксплуатации Страница: 22

DWT HKS12-54 5.1.17 Инструкция по эксплуатации онлайн [22/188] 860999

English

power tool, if they are not supervised or instructed

about use of the power tool by a person responsible

for their safety�

• Do not force the power tool. Use the correct

power tool for your application� The correct power

tool will do the job better and safer at the rate for which

it was designed�

• Do not use the power tool if the switch does

not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired�

• Disconnect the plug from the power source

and / or the battery pack from the power tool be-

fore making any adjustments, changing accesso-

ries, or storing power tools� Such preventive safety

measures reduce the risk of starting the power tool

accidentally�

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrained users�

• Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s op-

eration. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools�

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control�

• Use the power tool, accessories and tool bits

etc. in accordance with these instructions, taking

into account the working conditions and the work

to be performed. Use of the power tool for operations

different from those intended could result in a hazard-

ous situation�

• Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations�

• Note that when you operate a power tool, please

hold the auxiliary handle correctly, which is helpful

when controlling the power tool� Therefore, proper

holding can reduce the risk of accidents or injuries�

Service

• Have your power tool serviced by a qualied

repair person using only identical replacement

parts. This will ensure that the safety of the power tool

is maintained�

• Follow instruction for lubricating and changing ac-

cessories�

Special

safety warnings

Safety instructions for all saws cutting procedures

DANGER: Keep hands away from cutting

area and the blade. Keep your second

hand on auxiliary handle, or motor hous-

ing. If both hands are holding the saw, they

cannot be cut by the blade�

• Do not reach underneath the workpiece. The

guard cannot protect you from the blade below the

workpiece�

• Adjust the cutting depth to the thickness of the

workpiece. Less than a full tooth of the blade teeth

should be visible below the workpiece�

• Never hold piece being cut in your hands or

across your leg. Secure the workpiece to a stable

platform. It is important to support the work properly

to minimize body exposure, blade binding, or loss of

control� (Circular saw shall be correctly held and pro-

cessed workpiece shall be fastened as indicated in

gure 15).

• Hold the power tool by insulated gripping sur-

faces only, when performing an operation where

the cutting tool may contact hidden wiring or its

own cord. Contact with a "live" wire will also make

exposed metal parts of the power tool "live" and could

give the operator an electric shock�

• When ripping, always use a rip fence or straight

edge guide. This improves the accuracy of cut and

reduces the chance of blade binding�

• Always use blades with correct size and shape

(diamond versus round) of arbour holes. Blades

that do not match the mounting hardware of the saw

will run eccentrically, causing loss of control�

• Never use damaged or incorrect blade washers

or bolt. The blade washers and bolt were specially

designed for your saw, for optimum performance and

safety of operation�

Safety guidelines during

power tool operation

Further safety instructions for all saws

Kickback causes and related warnings

• kickback is a sudden reaction to a pinched, bound

or misaligned saw blade, causing an uncontrolled

saw to lift up and out of the workpiece toward the

operator;

• when the blade is pinched or bound tightly by

the kerf closing down, the blade stalls and the mo-

tor reaction drives the unit rapidly back toward the

operator;

• if the blade becomes twisted or misaligned in the

cut, the teeth at the back edge of the blade can dig

into the top surface of the wood causing the blade

to climb out of the kerf and jump back toward the

operator�

Kickback is the result of saw misuse and / or incor-

rect operating procedures or conditions and can be

avoided by taking proper precautions as given below�

• Maintain a rm grip with both hands on the

saw and position your arms to resist kickback

forces. Position your body to either side of the

blade, but not in line with the blade. Kickback

could cause the saw to jump backwards, but kick-

back forces can be controlled by the operator, if

proper precautions are taken�

• When blade is binding, or when interrupting

a cut for any reason, release the trigger and

hold the saw motionless in the material until the

blade comes to a complete stop. Never attempt

to remove the saw from the work or pull the saw

backward while the blade is in motion or kick-

back may occur. Investigate and take corrective

actions to eliminate the cause of blade binding�

• When restarting a saw in the workpiece, cen-

tre the saw blade in the kerf and check that saw

teeth are not engaged into the material. If saw

blade is binding, it may walk up or kickback from the

workpiece as the saw is restarted�

DWT HKS12-54 5.1.17 Инструкция по эксплуатации онлайн [22/188] 860999

Содержание

Похожие устройства