Ryobi ONE+ R18MS216-0 5133003597 Инструкция к товару онлайн [8/276] 861389

The product may move and tip if it is not adequately

secured.

Ŷ Set up and lock the cutting angles and depth before

making the cut.

Ŷ Secure the workpiece to the mitre saw base. Use the

clamp provided and, where necessary, use additional

clamps or holding mechanisms to prevent unintentional

movement of the workpiece while cutting.

Ɣ Check that the operation of the blade guards are not

restricted by the position of the workpiece.

Ɣ Ensure that the fence and other parts of the product

will not be cut as the blade lowers to the cutting

position.

Ŷ Start the motor and allow the blade to reach full speed

before slowly lowering it to cut the workpiece. Slide

the blade assembly backwards to complete the cut as

necessary.

Ŷ Allow the blade assembly to rise to its upper position

where the blade guards are fully closed. Switch off the

motor and allow the blade to come to a complete stop

before removing the workpiece or off-cuts, or before

reaching into the area of the blade.

%HIRUH¿UVWXVHHQVXUHWKDWWKHDQJOHRIWKHEHYHORUPLWUH

set on the product matches the angle to be produced on

the workpiece. Check this on a discarded piece of wood by

using a carpenter’s set or mitre square.

WARNING

The manufacturer strongly recommends that the product

is always securely mounted to a bench top.

:KHQWKHEDVHRIWKHSURGXFWLV¿UPO\VHFXUHGWRDEHQFK

top by four nuts, bolts and washers as instructed, the

SURGXFWFDQEHXVHGDWPD[LPXPEHYHODQGPLWUHVHWWLQJ

without the possibility of it tipping over. If the product is not

secured properly, the product may over balance when large

bevel angles are selected.

$WWKHIURQWRIWKHPLWUHVDZEDVHWKHUHLVDQH[WHQGLQJEDU

ZKLFKVKRXOGEHSXOOHGRXWWRLWVIXUWKHVWH[WHQW7KLVZLOO

help prevent the mitre saw from over balancing.

There is also an adjustable screw (balancing foot) that

H[WHQGV IURP WKH ERWWRPRI WKH H[WHQVLRQWXUQWDEOH 7KLV

VFUHZVKRXOGEHDGMXVWHGVRWKDWLWWRXFKHVWKHÀDWVXUIDFH

that the product is resting upon. This will also prevent the

SURGXFWIURPRYHUEDODQFLQJZKHQFXWWLQJDWWKHIXOOH[WHQW

of the slide and bevel. Beware, this part of the saw table

moves when different mitre angles are selected, so the

screw needs to be frequently adjusted and reset.

MAINTENANCE

Ŷ Do not modify the product in any way or use accessories

not approved by the manufacturer. Your safety and that

of others may be compromised.

Ŷ Do not use the product if any switches, guards or

other functions does not work as intended. Return to

an authorised service centre for professional repair or

adjustment.

Ŷ Do not make any adjustments whilst the saw blade is

in motion.

Ŷ Always make sure the battery pack has been removed

from the product before making adjustments, lubricating

or when doing any maintenance on the product.

Ŷ Before and after each use, check the product for

damage or broken parts. Keep the product in top

working condition by immediately replacing parts with

spares approved by the manufacturer.

Ŷ The blade has sharp edges and may also remain hot

DIWHUFXWWLQJRSHUDWLRQV([HUFLVHH[WUHPHFDXWLRQZKHQ

FOHDQLQJ DQ H[SRVHG EODGH :HDU JORYHV WR SURWHFW

yourself from personal injury.

Ŷ Clean the saw and its accessories from dust regularly,

especially moving parts including the blade guard.

Use a hand brush or vacuum cleaner to remove dust

effectively. Do not use compressed air.

Ŷ To assure safety and reliability, all repairs, including

changing brushes, should be performed by an

authorised service centre.

WARNING

Do not attempt to disassemble the blade guard assembly

for cleaning or repair. Damaged guards should not be

used. Return to an authorised service centre for repair

or replacement.

WARNING

For greater safety and reliability, all repairs should be

performed by an authorised service centre.

Mitre and bevel angle calibration

If mitre and bevel angle calibration are needed, see pages

±DQGIROORZWKHFDOLEUDWLRQLQVWUXFWLRQV

Maximum cutting depth stop

7KH PD[LPXP FXWWLQJ GHSWK VWRS LV WR SUHYHQW WKH VDZ

blade from cutting into the metal base of the unit.

WARNING

7KHPD[LPXPFXWWLQJGHSWKVWRSLVQRWXVHUDGMXVWDEOH

'RQRWDGMXVWWKHPD[LPXPFXWWLQJGHSWKVWRS

TRANSPORTATION AND STORAGE

Ŷ When storing the product, remove the battery pack.

Store the product in a secure place that is not accessible

to children.

Ŷ Clean the product using a brush and vacuum cleaner

before storage.

Ŷ If you remove the saw blade or keep spares with

the unit, ensure they are in the original packaging to

prevent injury.

To secure the product prior to movement:

Ŷ The product should be stored at the zero degree mitre

and bevel angle and locked in position. The slide should

be locked. The handle should be locked in the lower

(safe) position with the guards closed.

6 | English

Ryobi ONE+ R18MS216-0 5133003597 Инструкция к товару онлайн [8/276] 861389

Похожие устройства