Home
Главная
Ryobi
Болгарки (УШМ)
ONE+ R18AG-0 5133001903
Инструкция к угловой шлифмашине R18AG Страница: 3

Ryobi ONE+ R18AG-0 5133001903 Инструкция к угловой шлифмашине R18AG онлайн [3/98] 861674

English

SPECIAL SAFETY RULES

Safety Warnings Common for Grinding or Abrasive

Cutting-Off Operations:

■ This power tool is intended to function as a

grinder or cut-off tool. Read all safety warnings,

instructions, illustrations and specifications

provided with this power tool. Failure to follow all

instructions listed below may result in electric shock,

fire and/or serious injury.

■ Operations such as sanding, wire brushing or

polishing are not recommended to be performed

with this power tool. Operations for which the power

tool was not designed may create a hazard and cause

personal injury.

■ Do not use accessories which are not specifically

designed and recommended by the tool

manufacturer. Just because the accessory can be

attached to your power tool, it does not assure safe

operation.

■ The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their rated speed

can break and fly apart.

■ The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories cannot

be adequately guarded or controlled.

■ The arbour size of wheels, flanges, backing pads or

any other accessory must properly fit the spindle of

the power tool. Accessories with arbour holes that do

not match the mounting hardware of the power tool will

run out of balance, vibrate excessively and may cause

loss of control.

■ Do not use a damaged accessory. Before each use,

inspect the accessory such as abrasive wheels for

chips and cracks, backing pad for cracks, tear or

excess wear, wire brush for loose or cracked wires.

If power tool or accessory is dropped, inspect for

damage or install an undamaged accessory. After

inspecting and installing an accessory, position

yourself and bystanders away from the plane of

the rotating accessory and run the power tool at

maximum no-load speed for one minute. Damaged

accessories will normally break apart during this test

time.

■ Wear personal protective equipment. Depending

on application, use face shield, safety goggles or

safety glasses. As appropriate, wear dust mask,

hearing protectors, gloves and workshop apron

capable of stopping small abrasive or workpiece

fragments. The eye protection must be capable of

stopping flying debris generated by various operations.

The dust mask or respirator must be capable of filtrating

particles generated by your operation. Prolonged

exposure to high intensity noise may cause hearing

loss.

■ Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of

workpiece or of a broken accessory may fly away and

cause injury beyond immediate area of operation.

■ Hold power tool by insulated gripping surfaces

only, when performing an operation where the

cutting tool may contact hidden wiring. Contact with

a “live” wire will also make exposed metal parts of the

power tool “live” and could give the operator an electric

shock.

■ Position the cord clear of the spinning accessory.

If you lose control, the cord may be cut or snagged

and your hand or arm may be pulled into the spinning

accessory.

■ Never lay the power tool down until the accessory

has come to a complete stop. The spinning accessory

may grab the surface and pull the power tool out of your

control.

■ Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into

your body.

■ Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electrical hazards.

■ Do not operate the power tool near flammable

materials. Sparks could ignite these materials.

■ Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in

electrocution or shock.

Safety Warnings Specific for Grinding and Abrasive

Cutting-Off Operations:

■ Use only wheel types that are recommended for

your power tool and the specific guard designed

for the selected wheel. Wheels for which the power

tool was not designed cannot be adequately guarded

and are unsafe.

■ The guard must be securely attached to the power

tool and positioned for maximum safety, so the

least amount of wheel is exposed towards the

operator. The guard helps to protect operator from

broken wheel fragments, accidental contact with wheel

and sparks that could ignite clothing.

■ Wheels must be used only for recommended

applications. For example, do not grind with the

side of cut-off wheel. Abrasive cut-off wheels are

intended for peripheral grinding, side forces applied to

these wheels may cause them to shatter.

■ Always use undamaged wheel flanges that are of

correct size and shape for your selected wheel.

Proper wheel flanges support the wheel, thus reducing

the possibility of wheel breakage. Flanges for cut-off

wheels may be different from grinding wheel flanges.

■ Do not use worn down wheels from larger power

tools. Wheel intended for larger power tool is not

suitable for the higher speed of a smaller tool and may

Ryobi ONE+ R18AG-0 5133001903 Инструкция к угловой шлифмашине R18AG онлайн [3/98] 861674

Похожие устройства