Ryobi 18В RDD18-2C42S 5133005521 Инструкция к товару онлайн [3/84] 861768
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Ryobi 18В RDD18-2C42S 5133005521 Инструкция к товару онлайн [3/84] 861768

Ryobi 18В RDD18-1C20S 5133005519 Инструкция к товару онлайн [3/84] 861767
Safety, performance, and dependability have been given
top priority in the design of your drill driver.
INTENDED USE
The drill driver is intended to be used only by adults who
have read and understood the instructions and warnings
in this manual, and can be considered responsible for their
actions.
The product is intended for drilling into various materials,
including wood, metal, and plastics using a drill bit having
a shank diameter of less than 13 mm. The product can
be used to drive and remove screws and bolts using an
appropriate bit.
The product is intended for consumer use only.
Do not use the product for any other purpose. Use of the
SURGXFWIRURSHUDWLRQVGLႇHUHQWIURPLQWHQGHGFRXOGUHVXOWLQ
a hazardous situation..
WARNING! Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
PD\UHVXOWLQHOHFWULFVKRFN¿UHDQGRUVHULRXVLQMXU\
Save all warnings and instructions for future reference.
DRILL SAFETY WARNING
SAFETY INSTRUCTIONS FOR ALL OPERATIONS
Ŷ Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory or fasteners may contact hidden wiring.
Cutting accessory or fasteners contacting a “live” wire
may make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
SAFETY INSTRUCTIONS WHEN USING LONG DRILL
BITS
Ŷ Never operate at higher speed than the maximum
speed rating of the drill bit. At higher speeds, the bit is
likely to bend if allowed to rotate freely without contacting
WKHZRUNSLHFHUHVXOWLQJLQSHUVRQDOLQMXU\
Ŷ Always start drilling at low speed and with the bit
tip in contact with the workpiece. At higher speeds,
the bit is likely to bend if allowed to rotate freely without
FRQWDFWLQJWKHZRUNSLHFHUHVXOWLQJLQSHUVRQDOLQMXU\
Ŷ Apply pressure only in direct line with the bit and do
not apply excessive pressure. Bits can bend causing
EUHDNDJHRUORVVRIFRQWUROUHVXOWLQJLQSHUVRQDOLQMXU\
ADDITIONAL SAFETY WARNINGS
Ŷ Clamp workpiece with a clamping device. Unclamped
ZRUNSLHFHVFDQFDXVHVHYHUHLQMXU\DQGGDPDJH
Ŷ Dust created by operating the product can cause
UHVSLUDWRU\LQMXU\:HDUDSSURSULDWH GXVWFRQWURO PDVN
with filters suitable for protecting against particles from
the material being worked on.
Ŷ ,QMXULHV PD\ EH FDXVHG RU DJJUDYDWHG E\ SURORQJHG
XVHRIDWRRO:KHQXVLQJDQ\WRROIRUSURORQJHGSHULRGV
ensure you take regular breaks.
Ŷ Switch off the product immediately if the bit stalls. Do
not switch on the product again while the bit is stalled,
as doing so could trigger a sudden recoil with a high
reactive force. Determine why the bit stalled and rectify
this, paying heed to the safety instructions.
The possible causes may be:
– it is tilted in the workpiece
– it has pierced the workpiece
– the product is overloaded
Ŷ Ambient temperature range for tool during operation is
between 0Û&DQG40Û&
Ŷ Ambient temperature range for tool storage is between
0Û&DQG40Û&
Ŷ The recommended ambient temperature range for the
charging system during charging is between 10Û&DQG
38Û&
ADDITIONAL BATTERY SAFETY WARNINGS
Ŷ 7RUHGXFHWKHULVNRIILUHSHUVRQDOLQMXU\DQGSURGXFW
damage due to a short circuit, never immerse your
tool, battery pack or charger in fluid or allow fluid to
flow inside them. Corrosive or conductive fluids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
Ŷ Charge the battery pack in a location where the ambient
temperature is between 10°C and 38°C.
Ŷ Store the battery pack in a location where the ambient
temperature is between 0°C and 40°C.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps or
tape. Do not transport batteries that are cracked or leaking.
Check with the forwarding company for further advice.
KNOW YOUR PRODUCT
See page 57.
1. Gear selector
2. 7RUTXHDGMXVWPHQWULQJ
3. Keyless chuck
4. Direction of rotation selector
5. Variable speed trigger
6. Handle, insulated gripping surface
7. LED light
8. Battery port
9. Screw driver bit
10. Operator’s manual
11. Drill bit
12. Battery pack
13. Charger
MAINTENANCE
Ŷ The product should never be connected to a power
VXSSO\ ZKHQ DVVHPEOLQJ SDUWV PDNLQJ DGMXVWPHQWV
cleaning, performing maintenance, or when the product
is not in use. Disconnecting the product from the power
supply will prevent accidental starting that could cause
VHULRXVLQMXU\
Ŷ :KHQ VHUYLFLQJ XVH RQO\ RULJLQDO PDQXIDFWXUHU¶V
replacement parts, accessories and attachments. Use
of any other parts may create a hazard or cause product
damage.
3
Original Instructions
ENGLISH
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL

Похожие устройства

Скачать