Ryobi ONE+ R18N16G-120S 5133003859 Инструкция к товару онлайн [3/104] 862539

English

WARNING

Read all safety warnings and all instructions. Failure

to follow the warnings and instructions may result in

electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

NAILER SAFETY WARNINGS

a) Always assume that the tool contains fasteners.

Careless handling of the nailer can result in unexpected

firing of fasteners and personal injury.

b) Do not point the tool towards yourself or anyone

nearby. Unexpected triggering will discharge the

fastener causing an injury.

c) Do not actuate the tool unless the tool is placed

firmly against the workpiece. If the tool is not in

contact with the workpiece, the fastener may be

deflected away from your target.

d) Disconnect the tool from the power source when the

fastener jams in the tool. While removing a jammed

fastener, the nailer may be accidentally activated if it

is plugged in.

e) Use caution while removing a jammed fastener.

The mechanism may be under compression and the

fastener may be forcefully discharged while attempting

to free a jammed condition.

f) Do not use this nailer for fastening electrical cables.

It is not designed for electric cable installation and

may damage the insulation of electric cables thereby

causing electric shock or fire hazards.

ADDITIONAL SAFETY WARNINGS

a) Always be aware that misuse and improper handling of

this tool can cause injury to yourself and others.

b) The tool is designed for single-hand use. Do not hold

the tool by the front of the magazine. Do not put hands,

head, or other parts of your body near the bottom of

the magazine where the nail exits the tool, as serious

personal injury could be caused.

c) Always ensure that the workpiece contact is fully

positioned above the workpiece. Positioning the

workpiece contact only partially above the workpiece

could cause the nail to miss the workpiece completely

and result in serious personal injury.

d) Do not drive nails near edge of material. The workpiece

may split causing the nail to ricochet, injuring you or a

coworker. Be aware that the nail may follow the grain of

the wood, causing it to protrude unexpectedly from the

side of the work material or deflect, possibly causing

injury.

e) Keep hands and body parts clear of immediate work

area. Hold workpiece with clamps when necessary to

keep hands and body out of potential harm. Be sure

the workpiece is properly secured before pressing the

fastener against the material. The workpiece contact

may cause the work material to shift unexpectedly.

f) Keep face and body parts away from back of the tool

cap when working in restricted areas. Sudden recoil

can result in impact to the body, especially when nailing

into hard or dense material.

g) During normal use the tool will recoil immediately after

driving a fastener. This is a normal function of the tool.

Do not attempt to prevent the recoil by holding the nailer

against the work. Restriction to the recoil can result in

a second fastener being driven from the nailer. Grip

the handle firmly, let the tool do the work and do not

place second hand on top of tool or near exhaust at any

time. Failure to heed this warning can result in serious

personal injury.

h) Do not drive fasteners on top of other fasteners or with

the tool at an overly steep angle as this may cause

deflection of fasteners which could cause injury.

i) Always check the work area for hidden wiring, gas lines,

water lines, etc., before using the product on such work

area.

j) After using the product in the contact actuation mode,

switch it back to the full sequential mode.

k) The driving depth of the nail may be adjusted beyond

air pressure. It is advisable to test the depth on a scrap

workpiece to determine the required depth for the

application.

l) Only fasteners matching the description in the product

specification table can be used with this tool. Using

incorrect fasteners may lead to jamming or other

malfunctions.

DEPTH ADJUSTMENT SAFETY WARNINGS

a) Always remove the battery before adjusting the depth

of drive wheel.

b) Do not pull back on the adjustment wheel, the wheel is

designed to be rotated.

c) Do not press the trigger while adjusting the depth of

drive wheel.

d) Always select full sequential firing mode before

adjusting the depth of drive.

e) Do not point the tool towards yourself or anyone nearby

when adjusting the depth of drive.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national

provisions and regulations.

Follow all special requirements on packaging and labelling

when transporting batteries by a third party. Ensure that

no batteries can come in contact with other batteries

or conductive materials while in transport by protecting

exposed connectors with insulating, non-conductive caps

or tape. Do not transport batteries that are cracked or

Ryobi ONE+ R18N16G-120S 5133003859 Инструкция к товару онлайн [3/104] 862539

Похожие устройства