Home
Главная
Makita
Аккумуляторные
LXT 36 В DUH651Z
Инструкция к Makita DUH651Z Страница: 10

Makita LXT 36 В DUH651Z Инструкция к Makita DUH651Z онлайн [10/80] 862728

Cleaning the tool

Clean out the tool by wiping off dust with a dry or soap-

dipped rag.

Blade maintenance

Smear the blade before and once per hour during

operation using machine oil or similars.

NOTE:

•

Before smearing the blade, remove the chip receiver.

After operation, remove dust from both sides of the

blade with wired brush, wipe it off with a rag and then

apply enough low-viscosity oil, such as machine oil etc.

and spray-type lubricating oil.

CAUTION:

• Do not wash the blades in water. Failure to do so

may cause rust or damage on the tool.

Removing or installing shear blade

CAUTION:

• Before removing or installing shear blade, always

be sure that the tool is switched off and the battery

cartridge is removed.

• When replacing the shear blade, always wear

gloves without removing blade cover so that hands

and face does not directly contact the blade.

Failure to do so may cause personal injury.

NOTE:

• Do not wipe off grease from the gear and crank.

Failure to do so may cause damage to the tool.

• For specific way of removing and installing shear

blades refer to the reverse of a package for

accessory shear blades.

Removing the shear blades

Reverse the tool and loosen four screws.

Fig.18

NOTE:

• Be careful not to get your hands dirty as grease is

applied in the shear blade driving area.

Remove the under cover.

Fig.19

Remove the plate.

Fig.20

Set the crank at the angle as shown in the figure with a

slotted screwdriver.

Fig.21

Remove two screws from the shear blades and the

shear blade unit will be taken out.

Fig.22

CAUTION:

• Return the gear to the original position in such a

manner as it was installed if it should be taken

away by mistake.

Installing the shear blades

Prepare 4 removed screws (For under cover), 2 screws

(For shear blade), plate, under cover, and new shear

blades.

Adjust the crank position as shown in the figure. At this

time, apply some grease provided with new shear

blades to the periphery of the crank.

Fig.23

Overlap the oval hole in the upper blade with that in the

lower one.

Fig.24

Take out the blade cover from the old shear blades and

fit it onto the new ones for easy handling during the

replacement of blades.

Fig.25

Place the new shear blades on the tool so that the oval

holes in the shear blades fit onto the crank. Overlap the

holes in the shear blades with the screw holes in the

tool and then secure them with two screws.

Fig.26

Check the crank for smooth turn with a slotted

screwdriver.

Fig.27

Install the plate, under cover on the tool. Tighten the

screw firmly.

NOTE:

• There is no distinction between the top and bottom

of the plate.

Remove the blade cover and then turn on the tool to

check it for proper movement.

NOTE:

• When the shear blades does not operate properly,

there is a poor fit between the blades and crank.

Redo from the beginning.

Replacing carbon brushes

Fig.28

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Fig.29

Insert the top end of slotted screwdriver into the notch in

the tool and remove the holder cap cover by lifting it up.

Fig.30

Use a slotted screwdriver to remove the brush holder

caps. Take out the worn carbon brushes, insert the new

ones and secure the brush holder caps.

Reinstall the holder cap cover on the tool.

Makita LXT 36 В DUH651Z Инструкция к Makita DUH651Z онлайн [10/80] 862728

Похожие устройства