Home
Главная
Makita
Аккумуляторные
LXT 36 В DUH651Z
Инструкция к Makita DUH651Z Страница: 8

Makita LXT 36 В DUH651Z Инструкция к Makita DUH651Z онлайн [8/80] 862728

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before adjusting or

checking function on the tool.

Installing or removing battery cartridge

Fig.1

CAUTION:

• Always switch off the tool before installing or

removing of the battery cartridge.

• Hold the tool and the battery cartridge firmly

when installing or removing battery cartridge.

Failure to hold the tool and the battery cartridge

firmly may cause them to slip off your hands and

result in damage to the tool and battery cartridge

and a personal injury.

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator on the

upper side of the button, it is not locked completely.

CAUTION:

• Always install the battery cartridge fully until the

red indicator cannot be seen. If not, it may

accidentally fall out of the tool, causing injury to

you or someone around you.

• Do not install the battery cartridge forcibly. If the

cartridge does not slide in easily, it is not being

inserted correctly.

NOTE:

• The tool does not work with only one battery

cartridge.

Tool/ battery protection system

The tool is equipped with a tool/battery protection

system. This system automatically cuts off power to the

motor to extend tool and battery life.

The tool will automatically stop during operation if the

tool or battery are placed under one of the following

conditions. In some conditions, the indicators light up.

Overload protection

When the tool is operated in a manner that causes it to

draw an abnormally high current, the tool automatically

stops without any indication. In this situation, turn the

tool off and stop the application that caused the tool to

become overloaded. Then turn the tool on to restart.

Overheat protection for tool/ battery

When the tool/ battery is overheated, the tool stops

automatically without any indication. The tool does not

start even if pulling the switch trigger. In this situation,

let the tool/ battery cool before turning the tool on again.

NOTE:

The battery overheat protection works only with a

battery cartridge with a star marking.

Fig.2

Overdischarge protection

Fig.3

When the remaining battery capacity gets low, the

battery indicator blinks on the applicable battery side.

By further use, the tool stops and the battery indicator

lights up about 10 seconds. In this situation, charge the

battery cartridge.

Handle mounting positions

CAUTION:

• Always make sure that the handle is locked in the

desired position before operation.

Fig.4

Depending on the operations, you can set the angle of

the handle either 45°or 90°position on left or right. To

turn the handle, pull the knob and turn the handle as

shown in the figure. The handle is locked in 45°position.

To turn the handle to 90°position, pull the knob again

and turn the handle more.

Switch action

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger

actuates properly and returns to the "OFF"

position when released.

Fig.5

For your safety, this tool has a dual switching system.

To turn on the tool, press the lock-off button and press

the switch trigger A and B. To turn off the switch, release

either one of the switch triggers. The tool only starts

when pulling the both switch triggers.

Speed change

Fig.6

The strokes per minute can be adjusted just by turning

the adjusting dial. This can be done even while the tool

is running. The dial is marked 1 (lowest speed) to 6 (full

speed).

Refer to the table below for the relationship between the

number settings on the adjusting dial and the strokes

per minute.

Makita LXT 36 В DUH651Z Инструкция к Makita DUH651Z онлайн [8/80] 862728

Похожие устройства