Tesy gcv 1505620 d06 src 304062 Инструкция по эксплуатации онлайн [8/108] 864388
![Tesy gcv 1505620 d06 src 304062 Инструкция по эксплуатации онлайн [8/108] 864388](/views2/2102286/page8/bg8.png)
8 Instructions for use and maintenance
EN
V. MOUNTING AND SWITCHING ON
Attention! Improper installation and connection of the
appliance may make it hazardous for the health and life
of consumers. It may cause grievous and permanent
consequences, including but not limited to physical injuries and/
or death. Improper installation and connection of the appliance
may also lead to damage to the consumers’ property /damage
and/ or destruction/, or to that of third persons, as a result of, but
not limited to ooding, explosion and/or re.
Installation, connection to the main water and power supply, and
putting into operation must be carried out by certied electricians
and technical personnel certied in installation of this category of
appliances, who have obtained their license in the state where the
installation and commissioning of the appliance are carried out, and in
compliance with its local legislation.
1. Mounting
We recommend the mounting of the device at close proximity to
locations where hot water is used, in order to reduce heat losses
during transportation. In the event the device is mounted in a
bathroom, the selected location must exclude the possibility of
water spray contact from the showerhead or portable showerhead
attachment. Two methods of installation are possible:
•
Vertical installation (g. 1a, g. 1b) – When installing the
appliance onto a wall – the boiler should be hanged through the
upper carrying plank which is xed to the boiler shell.
Two hooks are used for suspending the appliance (min. Ø 10
mm) set rmly in the wall (not included in the mounting set).
The mounting bracket’s construction designed for water heaters
intended for vertical mounting is universal and allows a distance
between the hooks of 220 to 310 mm - g.1a; 440mm - g.1b.
•
Horizontal installation GCVH and GCH models (g.1c, 1d and
1e) – At horizontal installation the distances between the carrying
hooks are dierent with the dierent capacities and these values
are indicated in table 3 - g.1c and table 4 - g. 1d and g. 1e.
Warning! The appliance must be installed in such a
way, so as the protective plastic panel and the inlet/
outlet pipes to remain on the left side of the boiler (frontal
view). The cold water supply pipe (with a blue ring) must be
beneath the hot water discharge pipe (with a red ring).
Attention! In order to prevent injury to user and third
persons in the event of faults in the system for
providing hot water, the appliance must be mounted in
premises outtted with oor hydro insulation and plumbing
drainage. Don’t place objects, which are not waterproof under
the appliance under any circumstances. In the event of
mounting the appliance in premises not outtted with oor
hydro insulation, a protective tub with a plumbing drainage
must be placed under the appliance.
Notice: the set does not include a protective tub and the user
must select the same.
2. Water heater connection to the pipe network
Fig. 4: a) - for vertical installation; b) - for horizontal installation
GCVH; c) - for horizontal installation GCH;
Where: 1 - Inlet pipe; 2 - Safety valve; 3 - reducing valve (for water
main pressure > 0,6 MPa); 4 - Stop valve; 5 - Funnel connected to
the sewer network; 6 – Hose; 7 - Drain water tap.
Upon connecting the water heater to the water mains you must
consider the indicative color markings /rings/ axed to the pipes:
blue for cold /incoming/ water, red for hot /outgoing/ water.
The mounting of the safety return-valve supplied with the
water heater is obligatory. The safety return-valve must be
mounted on the cold water supply pipe, in observance of the
direction arrow stamped on its body, indicating the incoming
water’s direction. Additional stopcocks must not be mounted
between the safety return-valve and the water heater.
Exception: If the local regulations (norms) require the usage of
another protection valve or mechanism (in accordance with
EN 1487 or EN 1489), then it must be bought additionally. For
mechanisms operating in accordance with EN 1487 the announced
operational pressure must be no more than 0.7 MPa. For other
protection valves, the pressure at which they are calibrated must be
0.1 MPa lower than the one marked on the appliance’s sign. In these
cases the safety valve which the appliance is supplied with should
not be used.
Attention! The presence of other /old/ safety
return-valves may lead to a breakdown of your
appliance and they must be removed.
Attention! Other type of stopping armature is not
allowed between the protection return valve (the
protective device) and the appliance.
Attention! The attaching of the safety return-valve to
pipes with threads G ½ ‘’ longer than 10 mm is not
allowed, otherwise this may damage the valve and poses
danger for your appliance.
Attention! With boilers for vertical assembly, the safety
valve has to be connected to the ingoing pipe with the
safety plastic panel of the appliance being taken o. After it
has been assembled it should be in position as shown on Fig. 2.
Attention! The safety valve and the pipe between the
valve and the water heater must be protected from
freezing. During hose draining - its free end must be always
open to the atmosphere (not to be immersed). Make sure that
the hose is also protected from freezing.
Opening the cold-water stopcock of the water supply piping
network and opening the hot-water stopcock of the water-mixing
faucet carries out the lling of the water heater with water. After
the lling is complete, a constant stream of water must begin to
ow from the water-mixing faucet. Now you can close the hot
water stopcock.
In the event you must empty the water heater, rst you must cut
o its power supply. The inow of water from the water mains
must rst be terminated and the hot water tap of the mixing-
faucet must be opened. The water tap 7 (g 4a and 4 b) must be
opened to drain the water from water tank. If there is no such tap
build in the pipe line, than the water can be drain as follow:
•
Models equipped with safety valve with lever - You can drain
the water from the water heater by lifting the safety return-valve’s
lever. Water will drain from the safety return-valve’s drainage
opening
•
Models equipped with safety valve without lever - water can
be drain directly from inlet pipe of water tank after when you
disconnect it from water main
In the event of removing the ange, the discharge of several liters
of water, which remain in the water tank, is normal.
Attention!
Measures must be undertaken to prevent
damage from discharging water during draining.
In case that the pressure in the water mains is over the value
pointed out in the above paragraph I, then it is necessary to
assemble a pressure reduce valve, otherwise the water heater
would not function properly. The Manufacturer does not assume
any liability for problems arising out of the appliance’s improper
use.
3. Water heater connection to the electrical network.
Attention! Make sure the appliance is full of water prior
to switching on the electrical mains power.
Похожие устройства
- Tesy gcv 1505624c d06 s2r 304064 Инструкция по эксплуатации
- Tesy gcv 2005624c d06 s2rс 304065 Инструкция по эксплуатации
- Tesy TBRC GCR 1004424D B14 304950 Инструкция к TESY GCV 1004424D B14 TBRC 304945
- WURTH S3-KOFFR 07001022 961 1 Инструкция к товару
- Parpol V 500 400500 Сравнительные характеристики
- Parpol V 500 400500 Инструкция по эксплуатации
- Groz GR45505 Инструкция к Groz GR45505
- Berkut SP2070EP Инструкция к BERKUT SP2070EP
- Einhell GE-SC 35/1 Li Solo 3420650 Инструкция к Einhell GE*SC 35/1 Li*Solo 3420650
- Berkut SMART SP2000ЕР Инструкция к BERKUT SMART SP2000ЕР
- Berkut SP3030ЕР Инструкция к BERKUT SP3030ЕР
- Rothenberger ROCAL 20 61100 Инструкция по эксплуатации
- Einhell PXC GC-SC 36/31 LI-Solo 3420660 Инструкция по эксплуатации
- Калибр НБЦ-750 00000063214 Инструкция к Калибр НБЦ- 750 00000063214
- Daewoo DSC 3840Li без акб и зу Инструкция по эксплуатации
- Skipper 1.1 Bar, 90 л/мин SK-781 Инструкция
- Baxi ampera plus 6 E8403206-- Инструкция
- Термекс THERMEX Grizzly 5-12 Wi-Fi ЭдЭБ01987 Инструкция к Термекс THERMEX Grizzly 5-12 Wi-Fi ЭдЭБ01987
- Термекс THERMEX Skif 5-12 Wi-Fi ЭдЭБ02779 Инструкция к товару
- Термекс thermex stern 4-12 (тип b) 9 квт ЭдЭБ04123 Руководство