Metabo LF 724 S 600724000 Инструкция к товару онлайн [13/81] 867649
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Metabo LF 724 S 600724000 Инструкция к товару онлайн [13/81] 867649

Metabo LF 724 S 600724000 Инструкция к товару онлайн [13/81] 867649
ENGLISHen
12
Put the paint remover down and release locking
button.
Remove hexagonal wrench (9-a) and refit (9-b,
Torx).
Press the locking button (2) up to the stop and keep
pressed.
Radial reversible cutting plates:
Open protective flap. Turn cutter head with multi-
socket spanner until the reversible cutting blade is
accessible.
Remove the screws of the reversible blades (11)
with the Torx key(9-b). Loosen the reversible blade
(11) with the gravel and clean the support surface of
the reversible blades.
Insert the reversible blades (11) in such a way that
the sharp edges are pointing in the direction of
rotation.
If all edges are blunt, replace the reversible blade.
Always turn/replace both reversible blades!
Replace screws if the torx is damaged!
Tighten reversed/new reversible blades with 5 Nm.
Do not leave the Torx key in place!
9.3 Cleaning the cutter head and sliding
surface of the planing base
If required, clean the cutter head with agents
suitable for cleaning aluminium (pH value between
4.5 and 8).
9.4 Cleaning the extraction nozzle
During the milling operation, chips can get stuck in
the extraction nozzle (6) and clog the same.
Lodged chips can be loosened and removed
through the cleaning slit in the extraction nozzle
using the graver (8).
If required, remove the extraction nozzle (6).
Remove the Phillips screws and pull out the
extraction nozzle towards the rear. Clean extraction
nozzle (6) and planing base (10).
Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
For a complete range of accessories, see
www.metabo.com or the catalogue.
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Dispose of generated chips properly.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Directive 2002/
96/EC on waste electrical and electronic equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
P
1
=rated input power
P
2
=power output
n
0
=no-load speed
n
1
=on-load speed
m=weight
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~ AC Power
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. Depending on the operating
conditions, the condition of the power tool or the
accessories, the actual load may be higher or lower.
For assessment purposes, please allow for breaks
and periods when the load is lower. Based on the
adjusted estimates, arrange protective measures
for the user e.g. organisational measures.
Vibration total value
(vector sum of three directions)
determined in accordance with EN 60745:
a
h
=Vibration emission value (planing soft
wood)
K
h,SG
=Uncertainty (vibration)
10. Accessories
11. Repairs
12. Environmental Protection
13. Technical Specifications

Похожие устройства

Скачать