Home
Главная
Palram
Хозблоки и сараи
SKYLIGHT 6 ФУТОВ(6-3) 703387
Инструкция к Palram SKYLIGHT 703387 Страница: 10

Palram SKYLIGHT 6 ФУТОВ(6-3) 703387 Инструкция к Palram SKYLIGHT 703387 онлайн [10/74] 870614

IMPORTANT

Please read these instructions carefully before you start to assemble this product .

Please carry out the steps in the order set out in these instructions.

Keep these instructions in a safe place for future reference.

Safety Advice

For safety purposes we strongly recommend the product to be assembled by at least two people.

Some parts may have sharp edges. Please be careful when handling components. Always wear gloves,

eye protection, and long sleeves when assembling or performing any maintenance on your product.

Do not attempt to assemble the product in windy or wet conditions.

Do not attempt to assemble the product if you are tired, have taken drugs,

medications or alcohol, or if you are prone to dizzy spells.

Dispose of all plastic bags safely - keep them away from children's reach.

Keep children away from the assembly area.

When using a stepladder or power tools, make sure that you are following

the manufacturer's safety advice.

Do not climb or stand on the roof.

Do not hang or lay on the profiles.

Heavy articles should not be leaned against the poles.

Keep roof and gutters clear of snow, dirt & leaves.

Heavy snow load on the roof can make it unsafe to stand below or nearby.

Do not lean against or push the product during construction.

Hot items such as recently used grills, blowtorches etc. must not be stored inside the product.

Note: This product must be anchored on to a leveled surface and solid foundation to ensure its stability.

Make sure that screws and anchors are compatible with foundation type. Make sure that there are no

obstructions between the assembly area and the final position.

Cleaning Instructions

In order to clean the product, use a mild detergent solution and rinse with cold clean water.

Do not use acetone, abrasive cleaners, or other special detergents to clean the panels.

Clean the product once assembly is complete.

Before Starting Assembly

Choose your site carefully before beginning assembly.

The ground surface must be perfectly flat and leveled and have a solid base such as concrete,

asphalt, deck etc.

Complete site preparation before unpacking parts and beginning assembly.

Sort the parts and check against the content parts list.

Parts should be laid out close at hand. Keep all small parts (screws etc.) in a bowl so they do not get lost.

Please consult your local authorities if any permits are required prior to constructing the product.

During Assembly

MWhen encountering the information icon, please refer to the relevant assembly step

for additional comments and assistance.

This icon indicates

that the installer should

be inside the product.

Attention

This icon indicates that the

11 installer should be outside

the product.

Step 2: Place the back wall panel on the shed base panel according to the

stamped serial number (part #7701).

Door Assembly

Step 26, 27: Note that panels and profiles are connected in the right direction and

that profile holes are placed correctly as illustrated.

Step 29: Push aluminum profiles against part #8439 and then use Self-Drilling

screws (#4045) to connect to the profile (diagram b). No pre holes are needed.

Step 34: Anchor the shed on to a solid surface such as concrete, asphalt or wood deck; use suitable

screws and plugs. (Screws and plugs are not supplied).

*Tighten all screws when completing assembly.

Do not tighten screws and nuts (411 & 466) until completion of assembly process.

These 2 icons indicate if screws' tightening is required or not.

Note: Anchoring this product to the ground is essential to its stability and rigidity.

It is required to complete this stage in order for your warranty to be valid.

Palram SKYLIGHT 6 ФУТОВ(6-3) 703387 Инструкция к Palram SKYLIGHT 703387 онлайн [10/74] 870614

Похожие устройства