Iek КО-08Е Руководство по эксплуатации онлайн [2/7] 875514

Âñå ðàáîòû ïî ìîíòàæó è òåõíè÷åñêîìó îáñëóæèâàíèþ äîëæíû

ïðîèçâîäèòüñÿ ñ ñîáëþäåíèåì òðåáîâàíèé Ïðàâèë óñòðîéñòâà ýëåêòðîóñòàíîâîê,

Ïðàâèë òåõíè÷åñêîé ýêñïëóàòàöèè è Ïðàâèë òåõíèêè áåçîïàñíîñòè.

Ïî èñòå÷åíèè ñðîêà ñëóæáû è ïðè ñîõðàíåíèè èçäåëèåì ñâîåãî

ôóíêöèîíàëà, îíî íå ïðåäñòàâëÿåò îïàñíîñòè äëÿ äàëüíåéøåé ýêñïëóàòàöèè.

Basic product data

sizes of insulated and non-insulated lugs, connectors and sleeves

The jaws of tool ÊÎ-01, ÊÎ-02, ÊÎ-05Å, ÊÎ-06Å, ÊÎ-07Å, ÊÎ-09, ÊÎ-10 have

color and (or) digital markings, corresponding to the cross-section of crimped

conductors in the lug.

Operation rules

(hereinafter — the tool) is designed for crimping of various types and

Technical data

(hereinafter – lugs).

Additional technical data are given in table 3.

The tool should be used for crimping lugs, sleeves and conductors with a cross-

section corresponding to those specified in tables 1 è 2, for each version of the tool.

Otherwise, the quality of the crimping and the serviceability of the tool cannot be

guaranteed.

Tool ÊÎ-03Å, ÊÎ-04Å, ÊÎ-08Å, ÊÎ-13, ÊÎ-12, ÊÎ-11 equipped with a self-

adjusting jaw and a regulator of crimping force depending on the type of wire and lug.

Crimping tool of KO type ARMA2L 3 series of the IEK trademark

Overall dimensions of the tool are shown in figure 1.

Work with the tool in the following order:

Main technical data of the tool are presented in tables 1 and 2.

Safety precautions

IT IS FORBIDDEN

After the expiration of the service life and while maintaining the functionality of the

product, it does not pose a danger to further operation.

a) to bring the tool into the open position, it is necessary to bring the handles of the

tool to the stop or to press towards the crimping mechanism (jaws, self-adjusting jaw)

on the ratchet locking device located on the housing at the base of the tool;

All installation and maintenance works should be carried out in accordance with

the requirements of the Electrical Installations Code, Maintenance rules and Safety

instructions.

Tool are a non-repairable product and should be disposed of in case of breakage.

c) bring together tool handles. As the tool handles are brought together, the

ratchet mechanism fixes the degree of clamping and does not allow loosening the grip

until the jaws are fully closed or the ratchet locking mechanism is reset.

To crimp lugs under voltage (potential). To use the tool other than as intended.

b) press the lug into the crimping mechanism (seat of the jaws of the

corresponding section or the self-adjusting jaw) of the tool, then insert a conductor of

the corresponding section into the lug;