Rowenta Effective + DX1635D1 Руководство по эксплуатации онлайн [3/27] 881854
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Rowenta Effective + DX1635D1 Руководство по эксплуатации онлайн [3/27] 881854

Rowenta Effective + DX1635D1 Руководство по эксплуатации онлайн [3/27] 881854
4 5
The surfaces which are marked with this sign and
the soleplate are very hot during the use of the
appliances. Don’t touch these surfaces before the
iron is cooled down.
• If the electric power cord is damaged, it must be
replaced by an Approved Service Centre in order to
prevent any danger.
IMPORTANT RECOMMANDATIONS
• The voltage of your electrical installation must correspond to that of the iron (220-240V). Always plug your iron into an earth
socket. Connecting to the wrong voltage may cause irreversible damage to the iron and will invalidate the guarantee.
• If you are using a mains extension lead, ensure that it is corrected rated (16A) with an earth, and is fully extended.
• Do not unplug your appliance by pulling on the cord.
• Never immerse your steam iron in water or any other liquid. Never hold it under the water tap.
• Never touch the electric cord with the soleplate of the iron.
• Your appliance gives off steam, which may cause burns, especially when you are ironing close to the edge of your ironing board.
• Never direct the steam towards people or animals.
• For your saftey, this appliance conforms to the applicable standards and regulations (Low Voltage, Electromagnetic
Compatibility, Environmental Directives).
• This product has been designed for domestic use only. Any commercial use, inappropriate use or failure to comply with the
instructions, the manufacturer accepts no responsibility and the guarantee will not apply.
What water to use?
Your appliance has been designed to function with untreated tap water. If your water is very hard (check with your local water
authority), it is possible to mix untreated tap water with store-bought distilled or demineralised water in the following proportions:
- 50% tap water, - 50% distilled or demineralised water.
However, it is necessary to operate the Self clean function regularly in order to eliminate hard water deposits from the steam
chamber.
Use the Self clean function approximately every 2 weeks. If the water is very hard clean the iron weekly
Types of water not to use?
Heat concentrates the elements contained in water during evaporation.The types of water listed below contain organic waste or
mineral elements that can cause spitting, brown staining, or premature wear of the appliance: water from clothes dryers, scented
or softened water, water from refrigerators, batteries or air conditioners, pure distilled or demineralised water or rain water should
not be used in your Rowenta iron. Also do not use boiled, filtered or bottled water.
PLEASE RETAIN THIS INSTRUCTION
BOOKLET FOR FUTURE REFERENCE
Environnement
Environment protection first !
i
Your appliance contains valuable materials which can be recovered or recycled.
Leave it at a local civic waste collection point.
If there is a problem?
PROBLEM POSSIBLE CAUSE SOLUTION
Water drips from
the holes in the
soleplate.
You are using steam while the
iron is not hot enough.
Wait until the thermostat light
goes out.
You are using the shot of steam
button too often.
Wait a few seconds between each
use of the button.
You have stored the iron
horizontally, without emptying it
and without setting it to
.
See the section «Storing your iron».
Brown streaks
come through
the holes in the
soleplate and
stain the linen.
You are using ironing water
additives (i.e. scented water,
starch).
Never use ironing water additives;
these will permanently damage your
steam iron.
You are not using the right type
of water.
Perform a Self cleaning operation
and consult the chapter «What
water should I use?».
Your linen has not been rinsed
sufficiently or you have ironed a
new garment before washing it.
Make sure that your laundry is rinsed
sufficiently in order to remove any
deposits of soa p or chemical products
on new clothes.
The soleplate is
dirty or brown and
can stain the linen.
Your are ironing with an
inappropriate temperature
selection (temperature too high).
Clean the soleplate (refer to
chapter 11). Select the appropriate
program.
You have ironed over a printed
are of a garment.
Never iron over printed areas or
applications – always iron the
reverse side of such a garment.
There is little or no
steam.
The water tank is empty. Fill the water tank.
Your iron has been used dry for
too long.
Carry out a Self clean.
The soleplate
is scratched or
damaged.
You have placed your iron flat
on a metallic rest-plate or ironed
over a zip.
Refrain from ironing over metallic
buttons or zippers.
Steam or water
come from the iron
as you finish filling
the tank.
The steam control is not set to
the
position.
Check that the steam control is set
to the position.
The water tank is overfilled. Never exceed the Max level.
The spray does not
spray.
The water tank is not filled
enough.
Fill up the water tank.
Important notice for ≥ 2400W models only :
Under unfavorable mains conditions, phenomena like transient voltage drops or lighting fluctuations
can happen. Therefore, it is recommended that the iron is connected to a power supply system with
a maximum impedance of 0,29 Ω. If necessary, the user can ask the public power supply company
for the system impedance at the interface point.

Похожие устройства

Скачать