Home
Главная
Bort
Аккумуляторная Угловая Шлифмашина
BWS-20LI-SR
Руководство по эксплуатации Страница: 13

Bort BWS-20LI-SR Руководство по эксплуатации онлайн [13/52] 691073

the battery; avoid contact. If contact accidentally occurs,

ush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or burns.

Service

Have your power tool serviced by a qualied repair person

using only identical replacement parts. This will ensure

that the safety of the power tool is maintained.

SAFETY WARNINGS FOR ANGLE GRINDER

• This power tool is intended to function as a grinder,

sander, wire brush or cut-o tool. Read all safety warn-

ings, instructions, illustrations and specications provid-

ed with this power tool. Failure to follow all instructions

listed below may result in electric shock, re and/or se-

rious injury.

• Operations such as polishing are not recommended

to be performed with this power tool. Operations for

which the power tool was not designed may create a

hazard and cause personal injury.

• Do not use accessories which are not specically de-

signed and recommended by the tool manufacturer.

Just because the accessory can be attached to your

power tool, it does not assure safe operation.

• The rated speed of the accessory must be at least equal

to the maximum speed marked on the power tool.

Accessories running faster than their rated speed can

break and y apart.

• The outside diameter and the thickness of your acces-

sory must be within the capacity rating of your power

tool. Incorrectly sized accessories cannot be adequately

guarded or controlled.

• Threaded mounting of accessories must match the

grinder spindle thread. For accessories mounted by

anges, the arbour hole of the accessory must t the

locating diameter of the ange. Accessories that do not

match the mounting hardware of the power tool will

run out of balance, vibrate excessively and may cause

loss of control.

• Do not use a damaged accessory. Before each use in-

spect the accessory such as abrasive wheels for chips

and cracks, backing pad for cracks, tear or excess wear,

wire brush for loose or cracked wires. If power tool or

accessory is dropped, inspect for damage or install an

undamaged accessory. After inspecting and installing

an accessory, position yourself and bystanders away

from the plane of the rotating accessory and run the

power tool at maximum no-load speed for one minute.

Damaged accessories will normally break apart during

this test time.

• Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing protec-

tors, gloves and shop apron capable of stopping small

abrasive or workpiece fragments. The eye protection

must be capable of stopping ying debris generated by

various operations. The dust mask or respirator must be

capable of ltrating particles generated by your oper-

ation. Prolonged exposure to high intensity noise may

cause hearing loss.

• Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal

protective equipment. Fragments of workpiece or of a

broken accessory may y away and cause injury beyond

immediate area of operation.

• Hold the power tool by insulated gripping surfaces only,

when performing an operation where the cutting acces-

sory may contact hidden wiring or its own cord. Cutting

accessory contacting a “live” wire may make exposed

metal parts of the power tool “live” and could give the

operator an electric shock.

• Position the cord clear of the spinning accessory. If you

lose control, the cord may be cut or snagged and your

hand or arm may be pulled into the spinning wheel.

• Never lay the power tool down until the accessory has

come to a complete stop. The spinning wheel may grab

the surface and pull the power tool out of your control.

• Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could

snag your clothing, pulling the accessory into your body.

• Regularly clean the power tool’s air vents. The motor’s

fan will draw the dust inside the housing and excessive

accumulation of powdered metal may cause electrical

hazards.

• Do not operate the power tool near ammable materi-

als. Sparks could ignite these materials.

• Do not use accessories that require liquid coolants. Us-

ing water or other liquid coolants may result in electro-

cution or shock.

SAFETY WARNINGS FO BATTERY TOOL

• Use auxiliary handle(s), if supplied with the tool. Loss of

control can cause personal injury.

• Hold power tool by insulated gripping surfaces, when

performing an operation where the cutting accesso-

ry may contact hidden wiring or its own cord. Cutting

accessory contacting a “live” wire may make exposed

metal parts of the power tool “live” and could give the

operator an electric shock.

• Use suitable detectors to determine if utility lines are

hidden in the work area or call the local utility company

for assistance. Contact with electric lines can lead to re

and electric shock. Damaging a gas line can lead to ex-

plosion. Penetrating a water line causes property dam-

age or may cause an electric shock.

• Switch o the power tool immediately when the tool

insert jams. Be prepared for high reaction torque

that can cause kickback. The tool insert jams when:

Bort BWS-20LI-SR Руководство по эксплуатации онлайн [13/52] 691073

Похожие устройства