Home
Главная
Bort
Пила
BRS-12Li-G
Руководство по эксплуатации Страница: 13

Bort BRS-12Li-G Руководство по эксплуатации онлайн [13/44] 514586

the teeth pointed upwards) and reinserted again.

Removing the Saw Blade

Turn the locking sleeve 3 approx. 90° in the direction of

the arrow and hold. Remove the saw blade 1.

Dust / Chip Extraction

• Dust from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dust can cau-

se allergic reactions and/or lead to respiratory infections

of the user or bystanders.

• Certain dust, such as oak or beech dust, is considered

carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 lter-class respirator.

• Observe the relevant regulations in your country for the

materials to be worked.

• Prevent dust accumulation at the workplace. Dust can

easily ignite.

Working Advice

• Before any work on the machine itself (e. g. maintenan-

ce, tool change, etc.) as well as during transport and sto-

rage, remove the battery from the power tool.

• There is danger of injury when unintentionally actua-

ting the On/O switch.

• When sawing light building materials, observe the sta-

tutory provisions and the recommendations of the ma-

terial suppliers.

• Check wood, press boards, building materials, etc. for fo-

reign objects such as nails, screws or similar, and remove

them, if required.

• Switch the machine on and guide it toward the work-

piece. Position the base plate 2 onto the surface of the

work and saw through the material applying uniform

contact pressure and feed. After completing the wor-

king procedure, switch the machine o.

• If the saw blade should jam, switch the machine o im-

mediately.

• Widen the gap somewhat with a suitable tool and pull

out the machine.

Plunge Cutting

• The plunge cutting procedure is only suitable for trea-

ting soft materials such as wood, plaster board or simi-

lar!

• Do not work metal materials with the plunge cutting

procedure!

• Use only short saw blades for plunge cutting. Place the

machine with the edge of the ootplate 2 onto the work-

piece and switch on. For power tools with stroke speed

control, set the maximum stroke speed. Press the power

tool rmly against the workpiece and allow the saw bla-

de to slowly plunge into the workpiece.

• As soon as the footplate 2 fully lays on the surface of

the workpiece, continue sawing alongside the desired

cutting line.

• For certain work, the saw blade 1 can also be inserted

turned through by 180° and the sabre saw can be gui-

ded accordingly in a reversed manner.

Flush Cuts

• Using elastic bimetal saw blades, items still attached to

a wall (e. g. projecting building elements such as water

pipes, etc.) can be sawn o ush at the wall.

• Pay attention that the saw blade always extends be-

yond the diameter of the material being orked. There

is danger of kickback.

• Position the saw blade directly against the wall and

apply some lateral pressure via the tool until the foot-

plate faces against the wall. Switch the power tool on

and saw through the workpiece, applying constant

lateral pressure.

• Coolant/Lubricant

• When sawing metal, coolant/lubricant should be ap-

plied alongside cutting line because of the material

heating up.

MAINTENANCE AND CLEANING

Make sure that the machine is not live when carry-

ing out maintenance work on the motor.

• The anti-adhesive coating on the heating element

must be cleaned with nonadherent paper or a

non-fraying cloth and spirit or industrial alcohol before

each welding process. Any remnants of plastic adher-

ing to the heating element must be cleaned o in the

same way. In this process, take care to ensure that the

anti-adhesive coating on the heating element is not

damaged by tools.

• The machine requires no additional lubrication.

• Should a fault occur, e.g. after wear of a part, please

contact your local BORT GLOBAL LIMITED dealer.

DISPOSAL

Discarded electric appliances are recyclable and

should not be discarded in the domestic waste!

Please actively support us in conserving resourc-

es and protecting the environment by returning

this appliance to the collection centres (if available).

In order to prevent the machine from damage during

Bort BRS-12Li-G Руководство по эксплуатации онлайн [13/44] 514586

Похожие устройства