Home
Главная
Brayer
Шнековая соковыжималка
BR1701WH
Инструкция по эксплуатации Страница: 4

Brayer BR1701WH Инструкция по эксплуатации онлайн [4/23] 904074

6 7EN EN

• Do not touch the unit body, the power cord and the

power plug with wet hands.

• For child safety reasons do not leave polyethylene

bags used as packaging unattended.

ATTENTION! Do not allow children to play with

polyethylene bags or packaging lm. Danger of

su󰀨ocation!

• Do not repair the unit by yourself. Do not

disassemble the unit by yourself, if any malfunction

is detected, and after the unit was dropped, unplug it

and apply to the authorized service center.

• To avoid damages, transport the unit in the original

package.

• Keep the unit in a dry cool place out of reach of

children and disabled persons.

THE UNIT IS INTENDED FOR HOUSEHOLD USE

ONLY, DO NOT USE THE UNIT FOR COMMERCIAL

OR LABORATORY PURPOSES.

BEFORE THE FIRST USE

After unit transportation or storage at negative

temperature, unpack it and wait for 3 hours before

using.

• Unpack the unit and remove all the packaging

materials.

• Keep the original package.

• Read the safety measures and operating

recommendations.

• Check the delivery set.

• Examine the unit for damages, in case of damage do

not plug it into the mains.

• Make sure that specied specications of power

supply voltage of the unit correspond to the

specications of your mains. When the unit is used in

the mains with 60 Hz frequency, it does not need any

additional settings.

• The unit is not intended for usage by children.

• Do not leave children unattended to prevent using

the unit as a toy.

• Do not allow children to touch the operating surface,

the unit body, the power cord or the power plug

during operation of the unit.

• Be especially careful if children or disabled persons

are near the operating unit.

• During the unit operation and breaks between

operation cycles, place the unit out of reach of

children.

• The unit is not intended for usage by physically or

mentally disabled persons (including children) or by

persons lacking experience or knowledge if they are

not under supervision of a person who is responsible

for their safety or if they are not instructed by this

person on the usage of the unit.

• From time to time check the power cord integrity.

• If the power cord is damaged, it should be replaced

by the manufacturer, a maintenance service or

similar qualied personnel to avoid danger.

• Disassemble the Juicer and wash the parts that

come into contact with fruit and vegetables when the

Juicer is in use.

• Remove the pusher (9) from the feeding chute (1).

• Turn the feeding chute (1) with the lter element (2)

counterclockwise until the «▲» mark matches the «

» mark on the top of the motor unit and remove

them (Fig. 1).

• Remove the juice collector (4) from the motor unit

upwards (g. 2).

• Remove the auger (3) from the juice collector (4)

(g. 3).

• Wash the removed parts (1-2, 3, 4, 9), the juice cup

(7), the pulp container (8) and the cleaning brush (10)

with warm water and a neutral detergent, then rinse

and dry.

• Wipe the motor unit with a slightly damp cloth, then

dry.

JUICE EXTRACTOR ASSEMBLING

• Place the juice extractor on an even, dry and stable

surface so that an electrical outlet is always easily

accessible.

• Make sure before assembling the juice extractor

that the silicone seal on the underside of the juice

collector (4) is in place (g. 4).

Notes: the silicone seal must t tightly into its place of

installation, otherwise the juice may ow out of the juice

collector (4) during the operation and damage the juice

extractor.

• Install the juice collector (4) on the motor unit (g. 5).

• Install the auger (3) into the juice collector (4), make

sure that the auger (3) is correctly installed, it must

be mounted on the driving shaft and sink slightly into

the juice collector (4), otherwise the installation of the

lling chute (1) with the lter element (2) will not be

possible.

• Install the feeding chute (1) with the lter element (2)

on the juice collector (4), the «▲» mark must match

the « » mark on the top of the motor unit, turn the

feeding chute (1) with the lter element (2) clockwise

to «

» (Fig. 7). Make sure the feeding chute (1) with

the lter element (2) are securely xed.

• Insert the pusher (9) into the feeding chute (1).

• Place the juice cup (7) under the spout (5) and install

the pulp container (8) (g. 8).

• The juice exractor is ready for use.

TIPS

• The Juicer is not intended for extracting juice from

fruits, containing high levels of

• pectin or starch, such as bananas, papayas, gs,

avocados, and etc., bananas contain little to no juice,

only add them for the scent.

• The Juicer is not intended to process too hard high-

ber foods, such as, coconuts, quinces, rheum, and

etc.

• Use other types of kitchen appliances to process

those kinds of food.

Brayer BR1701WH Инструкция по эксплуатации онлайн [4/23] 904074

Похожие устройства