![Tp-Link T1600G-28TS (TL-SG2424) Руководство по установке онлайн [2/32] 174202](/img/pdf.png)
Tp-Link T1600G-28TS (TL-SG2424) Руководство по установке онлайн [2/32] 174202
Содержание
- Installation guide 1
- Jetstream gigabit smart switch 1
- Ce mark warning 3
- Copyright trademarks 3
- Fcc statement 3
- About this installation guide 4
- Audience 4
- Conventions 4
- Related document 4
- Appendix a troubleshooting 24 5
- Appendix b hardware specifications 25 5
- Chapter 1 introduction 01 5
- Chapter 2 installation 08 5
- Chapter 3 lightning protection 13 5
- Chapter 4 connection 19 5
- Chapter 5 configuration 21 5
- Contents 5
- Appearance 6
- Chapter 1 introduction 6
- Front panel 6
- Product overview 6
- 100 1000mbps rj45 port 7
- Designed to connect to the device with a bandwidth of 10mbps 100mbps or 1000mbps each has a corresponding link act led and a 1000mbps led 7
- Designed to install the sfp module t1600g 28ts features 4 individual sfp ports and supports 1000m sfp module connection only 7
- Introduction 7
- Jetstream gigabit smart switch 7
- Press this button for 5 seconds or above to reset the software setting back to factory default settings 7
- Sfp port 7
- The front panel of t1600g 52ts is shown as the following figure 7
- 100 1000mbps rj45 port 8
- Designed to connect to the device with a bandwidth of 10mbps 100mbps or 1000mbps each has a corresponding 10 100 1000mbps led 8
- Designed to install the sfp module t1600g 52ts features 4 individual sfp ports and supports 1000m sfp module connection only 8
- Introduction 8
- Jetstream gigabit smart switch 8
- Sfp port 8
- T1600g 28ps has an led mode switch button which is for switching the led status indication when the speed led is on the port led is indicating the data transmission status when the poe led is on the port led is indicating the power supply status by default the speed led is on pressing the mode switch button 8
- The front panel of t1600g 28ps is shown as the following figure 8
- Introduction 9
- Jetstream gigabit smart switch 9
- The speed led will turn off and the poe led will light up then the poe led will turn off after being on for 60 seconds and the speed led will light up again 9
- When the poe led is on the port led is indicating the power supply status 9
- When the speed led is on the port led is indicating the data transmission status 9
- 100 1000mbps rj45 port 10
- Led mode switch button 10
- Sfp port 10
- Introduction 11
- Jetstream gigabit smart switch 11
- Led mode switch button 11
- Press this button for five seconds or above to reset the software setting back to factory default settings 11
- Press this button to switch the led status indication between speed and poe 11
- When the poe led is on the port led is indicating the power supply status 11
- 100 1000mbps rj45 port 12
- Grounding terminal 12
- Kensington security slot 12
- Power socket 12
- Rear panel 12
- Sfp port 12
- Chapter 2 installation 13
- Package contents 13
- Safety precautions 13
- Clearness 14
- Electromagnetic interference 14
- Site requirements 14
- Temperature humidity 14
- Installation site 15
- Installation tools 15
- Lightning protection 15
- Desktop installation 16
- Product installation 16
- Rack installation 16
- Cabling reasonably 18
- Chapter 3 lightning protection 18
- Requirements for cabling outdoors 18
- Jetstream gigabit smart switch 19
- Lightning protection 19
- Note the above minimum net length height is required when metal raceway is not used if any requirements cannot be met you can add a steel tube or metal raceway for shielding 19
- Requirements for cabling indoors 19
- Requirements for the distance between ethernet cable and high power electric devices are in following tables 19
- Requirements for the distance between ethernet cable and other pipelines are shown in the table 19
- The main cable should be paved in the metal raceway of the access shaft when cabling keep the loop area formed by the cable itself as small as possible 19
- The two diagrams below demonstrate parallel net length and parallel overlapping net height 19
- When cabling indoors keep a certain distance away from the devices that may cause high frequency interferences such as down conductor cable powerline power transformer and electromotor 19
- Connect to ground 20
- Connecting the device to ground is to quickly release the lightning over voltage and over current of the device which is also a necessary measure to protect the body from electric shock 20
- Connecting to the grounding bar 20
- If the device is installed in the equipment room where a grounding bar is available you are recommended to connect the device to the grounding bar as shown in the following figure 20
- In different environments the device may be grounded differently the following will instruct you to connect the device to the ground in two ways connecting to the grounding bar or connecting to the ground via the power cord please connect the device to ground in the optimum way according to your specific operation environment 20
- Jetstream gigabit smart switch 20
- Lightning protection 20
- Connecting to the ground via the power supply 21
- Equipotential bonding 21
- Use lightning arrester 22
- Chapter 4 connection 24
- Ethernet port 24
- Sfp port 24
- Verify installation 24
- Initialization 25
- Power on 25
- Chapter 5 configuration 26
- Configure the switch via gui 26
- Configure the switch using cli 27
- Appendix a troubleshooting 29
- Q1 what could i do if i forgot the username and password of the switch 29
- Q2 why does the pwr led work abnormally 29
- Q3 what could i do if i could not access the web based configuration page 29
- Appendix b hardware specifications 30
- Jetstream gigabit smart switch 30
Похожие устройства
- Tp-Link T1600G-28TS (TL-SG2424) Руководство пользователя
- Rivotek Fisher 25 Pro Руководство пользователя
- Rivotek Fisher 51 Руководство пользователя
- Liberton D-LED 4016 DBT2 Руководство по эксплуатации
- Liberton D-LED 3216 DBT2 Руководство по эксплуатации
- Liberton D-LED 2216 DBT2 Руководство по эксплуатации
- Liberton D-LED 32303 DBT2 Руководство по эксплуатации
- Liberton D-LED 24306 DBT2 Руководство по эксплуатации
- Liberton D-LED 3203 DBT2 Руководство по эксплуатации
- Philips SHE3590/10 Red Инструкция по эксплуатации
- Philips D 1202 B Инструкция по эксплуатации
- Philips HR 1560/20 Инструкция по эксплуатации
- Philips DCM2260/12 Black Инструкция по эксплуатации
- Philips BT5880B/12 Black Инструкция по эксплуатации
- Philips SC1981/00 Инструкция по эксплуатации
- Philips HP8320/00 Essential Care Инструкция по эксплуатации
- Philips MCM2050/12 Black Инструкция по эксплуатации
- Philips HX6042/07 Инструкция по эксплуатации
- Philips BT 7500 Black Инструкция по эксплуатации
- Philips BM5B/00 Black Инструкция по эксплуатации