Home
Главная
Vitesse
Утюг
VS-664
Инструкция по эксплуатации Страница: 3

Vitesse VS-664 Инструкция по эксплуатации онлайн [3/6] 175678

Anti-calc system

A special resin filter inside the water reservoir softens the water and prevents

scale build-up in the plate. The resin filter is permanent and does not need

replacing.

Please Note:

Use tap water only. Distilled and/de-mineralised water makes the "Zero-

Calc" anti-calc system ineffective by altering its physicochemical

characteristics.

Do not use chemical additives, scented substances or de-calcifiers. Failure

to comply with the above-mentioned regulations leads to the loss of

guarantee.

Anti-drip system

With the anti-drip system, you can perfectly iron even the most delicate

fabrics.

Always iron these fabrics at low temperatures. The plate may cool down to

the point where no more steam comes out, but rather drops of boiling

water that can leave marks or stains. In these cases, the Anti-drip system

automatically activates to prevent vaporization, so that you can iron the

most delicate fabrics without risk of spoiling or staining them.

General instructions

When using the iron for the first time, you may notice a slight emission of

smoke and hear some sounds made by the expanding plastics. This is quite

normal and it stops after a short time. We also recommend passing the iron

over an ordinary cloth before using it for the first time.

Preparations

Soft the laundry to be ironed according to the international symbols on the

garment label, or if this is missing, according to the type of fabric.

S t a r t i r o n i n g t h e g a r m e n t s r e q u i r i n g a l o w t e m p e r a t u r e .

This reduces the waiting times (the iron takes less time to heat up than to

cool down) and eliminates the risk of scorching the fabric.

GARMENT

LABEL

FABRIC

TYPE

THERMOSTAT

REGULATION

synthetic

silk - wool

Cotton - linen

•

low temperature

••

medium temperature

Fabric not to be ironed

•••

high temperature

Steam ironing

Filling with water

Fill the water re-servoir before using the steam function or the spray nozzle.

Remove the plug from the wall socker before filling the re-servoir.

1. this steam iron is to a large extent resistant to hard water (up to 15 DH).

Although to hand water may be used,it is advisable to use distilled,

de-mineralised or decalcified water.Should you be unsure about the

hardness of the relevant local authority department.

2. Push the locking button for the water re-servoir and remove it by pulling it

out from the front.

3. Open the over of the water Filler door

4. Fill the empty water re-servoir. Fill to the indicated “MAX” level only.

5. Close the water Filler door.

6. Fit the water re-servoir to the iron from the front and make sure that it

locked properly into place.

Selecting the temperature.

1. Put the iron in a vertical position.

2. Put the plug in the socket.

3. Adjust the thermostat knob for temperature regulation (13) according

to the international symbol on the garment label. The plate temperature

control light (6)indicates that the iron is heating up. Wait until the

indicator lamp goes off before ironing.

Warning: during ironing, the indicator lamp (12) comes on at intervals,

indicating that the selected temperature is maintained. If you lower the

thermostat temperature after ironing at a high temperature, do not start

ironing until the plate temperature control light comes on again.

Selecting the steam.

The quantity of steam is regulated by the variable steam control (4).

1. Move the variable steam control to a position between minimum and

maximum depending on the quantity of steam required and the

temperature selected.

Warning: the iron gives off steam continuously only if you hold the iron

horizontally. You can stop the continuous steam by placing the iron in a

vertical position or by moving the variable steam control to “0”. As

indicated on the thermostat knob for temperature regulation (13) and in

the initial table, you can only use steam at the highest temperatures. If the selected

temperature is too low, water may drip onto the plate.

Selecting Shot-steam and steam when ironing vertically.

Press the shot-steam button (6) to generate a powerful burst of steam that

can penetrate the fabrics and smooth the most difficult and tough creases.

Wait for a few seconds before pressing again.

By pressing the shot-steam button at intervals you can also iron vertically

(curtains, hung garments, etc.).

P/3 P/4

Содержание

Похожие устройства

iffnrrr w M if tw hti www vitesse ru Anti calc system A special resin filter inside the water reservoir softens the water and prevents scale build up in the plate The resin filter is permanent and does not need replacing Please Note Use tap water only Distilled and de mineralised water makes the ZeroCalc anti calc system ineffective by altering its physicochemical characteristics Do not use chemical additives scented substances or de calcifiers Failure to comply with the above mentioned regulations leads to the loss of guarantee Anti drip system With the anti drip system you can perfectly iron even the most delicate fabrics Always iron these fabrics at low temperatures The plate may cool down to the point where no more steam comes out but rather drops of boiling water that can leave marks or stains In these cases the Anti drip system automatically activates to prevent vaporization so that you can iron the most delicate fabrics without risk of spoiling or staining them General instructions When using the iron for the first time you may notice a slight emission of smoke and hear some sounds made by the expanding plastics This is quite normal and it stops after a short time We also recommend passing the iron over an ordinary cloth before using it for the first time Preparations Soft the laundry to be ironed according to the international symbols on the garment label or if this is missing according to the type of fabric GARMENT LABEL FABRIC TYPE THERMOSTAT REGULATION synthetic low température silk wool medium température Cotton linen high température Fabric not to be ironed Start ittffnilvg the g arments requiring a low temperature This reduces the waiting times the iron takes less time to heat up than to cool down and eliminates the risk of scorching the fabric P 3 Steam ironing Filling with water Fill the water re servoir before using the steam function or the spray nozzle Remove the plug from the wall socker before filling the re servoir 1 this steam iron is to a large extent resistant to hard water up to 15 DH Although to hand water may be used it is advisable to use distilled de mineralised or decalcified water Should you be unsure about the hardness of the relevant local authority department 2 Push the locking button for the water re servoir and remove it by pulling it out from the front 3 Open the over of the water Filler door 4 Fill the empty water re servoir Fill to the indicated MAX level only 5 Close the water Filler door 6 Fit the water re servoir to the iron from the front and make sure that it locked properly into place Selecting the temperature 1 Put the iron in a vertical position 2 Put the plug in the socket 3 Adjust the thermostat knob for temperature regulation 13 according to the international symbol on the garment label The plate temperature control light 6 indicates that the iron is heating up Wait until the indicator lamp goes off before ironing Warning during ironing the indicator lamp 12 comes on at intervals indicating that the selected temperature is maintained If you lower the thermostat temperature after ironing at a high temperature do not start ironing until the plate temperature control light comes on again Selecting the steam The quantity of steam is regulated by the variable steam control 4 1 Move the variable steam control to a position between minimum and maximum depending on the quantity of steam required and the temperature selected Warning the iron gives off steam continuously only if you hold the iron horizontally You can stop the continuous steam by placing the iron in a vertical position or by moving the variable steam control to 0 As indicated on the thermostat knob for temperature regulation 13 and in the initial table you can only use steam at the highest temperatures If the selected temperature is too low water may drip onto the plate Selecting Shot steam and steam when ironing vertically Press the shot steam button 6 to generate a powerful burst of steam that can penetrate the fabrics and smooth the most difficult and tough creases Wait for a few seconds before pressing again By pressing the shot steam button at intervals you can also iron vertically curtains hung garments etc P 4

Скачать