Home
Главная
Vitesse
Машинка Для Стрижки
VS-379
Руководство по эксплуатации Страница: 3

Vitesse VS-379 Руководство по эксплуатации онлайн [3/6] 179300

• Blades must be realigned if they have been removed for cleaning or

replacement.

• To realign the blades,simply match the upper

and bottom blades teeth up,point for point. (End

of top blade teeth should be approximately

1.2mm back from bottom blade.Compare your

clipper blades with the sketch.) (Fig.23)

• If blade alignment is incorrect,add afew drops of

oil to the blades,turn clipper on for a few

moments,turn off and unplug.Loosen screws

slightly and adjust.Tighten screws after blade is

aligned.(Fig.24)

Oil

• To maintain your clipper in peak condition,the blades should be oiled every

few haircuts.

• Do not use hair oil grease,oil mixed with kerosene

or any solvent.As the solvent will evaporate and

leave the thick oil which may slow down the blades

motion.(Fig.25)

Power screw

• The power screw permits you to adjust the

power.It has been adjust before leaving the factory.However,if the voltage

in your home is low,you may need to re-adjust it.

• To adjust,use a screwdriver or a thin coin to turn power screw in clockwise

direction until the arm strikes the coil,making a noise,Then slowly turn

power screw out (counter-clockwise)just until noise stops.This is

maximum power setting.(Fig.26)

Adjustable lever

• The lever is conveniently located near your

thumb(if you’re right-handed)so it can

easily be adjusted while the clipper is in your hand.

• The lever adds versatility to your clipper by allowing you to gradually

change the closeness of your cut without an attachment comb.

• When the lever is in the uppermost oisition,the blades will give you the

closest cut and leave the hair very short. Pushing the lever downward

gradually increases the cutting length.

• In its lowest position,the lever will leave the hair approximately the same

length as a #1 comb.

OUTLINING

• Outlining requires no attachments.Take the clipper and

push the lever up to the close-cut position.

• Comb hair into the style.Potition clipper between the side

burns and the ear. (Fig. 17)

• Make sure the corneredge of the blade is against the

hairline.With the outline of the hair as your guide,slowly

move the clipper over,around,and behing the ears.(Fig.18)

• For the back of the neck and the sideburns,hold the clipper

upside down,(see sketch),and holding it against the skin at

the length desired,move downwards.

Short cuts to perfect flat tops,crew cuts.

• Always cut from the back of the neck to the crown,using the

longest attachment comb.Holding it flat against the

head,slowly move the clipper up through the hair.

• Use the same technique for the sides,cutting from the

bottom to the upper side of the head.(Fig.19)

• For afront to the crown,cut the hair against the direction in

which it grows.Then even it up with the sides.(Fig20)

• For a flat top,use a flat comb,not the attachment comb.Just

cut hair on top of the head over it.

• To taper hair down to the neckline,use closer cutting

attachment combs.Comb hair and check for uneven spots

and outline sideburns and neckline. (Fig. 21)

• If a short tapered cut on the sides and back is

desired,follow the (Fig.22)

• The four basic areas illustrated on the hair cutting guide are your “road

map” to easy do-it-yourself hair cutting.

Maintenance

• Your clippers were carefully examined to ensure that the blades were oiled

and aligned before leaving our factory.

P/3 P/4

www.vitesse.ru

Vitesse VS-379 Руководство по эксплуатации онлайн [3/6] 179300

Содержание

Похожие устройства