Home
Главная
Felisatti
Фрезер
rf30/750 136040170
Инструкция по эксплуатации Страница: 3

Felisatti rf30/750 136040170 Инструкция по эксплуатации онлайн [3/18] 192307

TECHNICAL DATA

Router/trimmer RF30/750

Input power W 750

No-load speed rpm 27000

Clip diameter mm 1/8”

pprox. weight (without acces.) kg 1.9

The instructions contained in this manual must be strictly

followed, it should be carefully read and kept close at

hand to use when carrying out maintenance on the

indicated parts.

If the machine is used carefully and normal maintenance

is carried out, it will work well for a long time.

The functions and use of the tool you have bought shall

be only those described in this manual. Any other use

of the tool is strictly forbidden.

ILLUSTRATIONS

DESCRIPTION (See figures)

C Start-up switch (Fig.1)

D Clamping nut (Fig.1)

EQUIPMENT

- Clip,  1/8”

- Clip,  8 mm

- Fixed spanner 13 mm

- Fixed spanner 17 mm

- Operating instructions

- Safety instructions

- Warranty

SAFETY INSTRUCTIONS

 See “Safety Instructions” manual, supplied with this

instruction manual.

 For your personal safety, always connect the machine

to a mains supply protected by a differential and ther-

mal cutout switch, in accordance with regulations on

low-voltage wiring sitemaps.

 Do not pierce the motor housing as this could damage

the double insulation (use adhesive labels).

 Always unplug the machine before carrying out work

on it.

 Always stop the machine by switching it off, not by

unplugging it.

 WARNING! Before each use, inspect the plug and

lead. Should they need replacing, have this done by an

official service centre.

 Always keep the mains lead clear of the working range

of the machine.

 Only plug the machine in when it is switched off.

 Hold the machine firmly in both hands and in a stable

position.

 When working with the machine, always wear safety

goggles and ear protection. Other personal protection

equipment such as dust masks, gloves, helmet and

apron should be worn when necessary, along with non-

slip safety footwear. A dust mask is required when the

dust from the material deburred, such as paint or other

coating, is harmful. If in doubt, use safety equipment.

 Make sure the vents are free when working with dust. If

they require cleaning, first unplug the machine, do not

use metal objects and avoid damaging internal parts.

BEFORE USING THIS TOOL

Before using the tool, make sure the mains voltage is

correct: it must be the same as that on the specification

label. Machines with 230V can also be connected to a

220-V mains supply.

STARTING THE TOOL

Plug the machine in with the switch off.

Start the machine by turning the switch to position 1

("ON"). To switch off, do the same in reverse.

Fitting to the power tool (Mod. 90092.0000)

Remove the collet and the nut from the spindle of the

tool. Remove the 8 mm collet and fit the ⅛" one, fit the

⅛" bit and tighten the nut to fasten it. Fit accessory

90092.0000 by loosening screw A and fitting it in the

collar of the tool. Then tighten screw A to secure it.

DEPTH ADJUSTMENT

With the accessory securely fitted to the tool and the bit

in place, loosen the regulator set screw B, and move up

and down until the required depth is obtained. Tighten

the regulator set screw B to secure.

Warning: Bits should be specially cut for plaster or PVC.

ACCESSORIES

Accessories and their corresponding order number can

be found in our catalogues.

MAINTENANCE AND CARE

WARNING! Always unplug the machine before carrying

out work on it.

- Inspect the mounting screws: Regularly inspect all

the mounting screws and ensure they are firmly tight-

ened. Should any screw be loose, tighten it immedi-

ately. Failure to do so could put you at serious risk.

- Motor maintenance: Always take the greatest care

over this and make sure that the motor winding is not

damaged and does not become wet with oil or water.

- The vents should always be kept clean and free of

obstacles.

- Clean the machine thoroughly after each use. Blast the

motor regularly with compressed air.

- Check that the mains lead is in good condition. If it is

not, take it to an Official Service Centre to have it

replaced.

- Brush replacement: The brushes should be replaced

after 150 - 200 hours use or when they are less than

10 mm long. Have this done by an Official Service

Centre. We recommend that at every second change

of brushes, you take the machine to one of our Official

Service Centres for general cleaning and oiling.

Felisatti rf30/750 136040170 Инструкция по эксплуатации онлайн [3/18] 192307

Похожие устройства