Ryobi + набор бит rak17sd r18pd-ll25t Инструкция по эксплуатации онлайн [3/116] 198568
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Ryobi + набор бит rak17sd r18pd-ll25t Инструкция по эксплуатации онлайн [3/116] 198568

Ryobi + набор бит rak17sd r18pd-ll25t Инструкция по эксплуатации онлайн [3/116] 198568
English
1
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
EL
TR
UK
Safety, performance, and dependability have been given
top priority in the design of your percussion drill.
INTENDED USE
The percussion drill is intended to be used only by adults
who have read and understood the instructions and
warnings in this manual, and can be considered responsible
for their actions.
The percussion drill is intended to be used in drilling into
various materials, including wood, metal, and plastic using
a drill bit having a diameter of less than 13 mm. When in
impact mode, the percussion drill can be used in drilling
masonry and similar materials. When in screwdriving
mode, the percussion drill can be used in driving screws.
Do not use the product in any way other than those stated
for intended use.
WARNING
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
PERCUSSION DRILL SAFETY WARNINGS
■ Wear ear protectors when impact drilling. Exposure
to noise can cause hearing loss.
■ Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
■ Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a “live” wire may make exposed
metal parts of the power tool “live” and could give the
operator an electric shock.
■ Hold power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting a
“live” wire may make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
■ Do not operate on materials (e.g., asbestos) that
present a health hazard.
■ Switch off the product immediately if the bit stalls. Do
not switch on the product again while the bit is stalled,
as doing so could trigger a sudden recoil with a high
reactive force. Determine why the bit stalled and rectify
this, paying heed to the safety instructions.
The possible causes may be:
– it is tilted in the workpiece
– it has pierced the workpiece
– the product is overloaded
■ Sawdust and splinters must not be removed while the
product is running.
■ When working in walls, ceilings, or floors, avoid
electrical cables and gas or water pipes.
■ Secure your workpiece with a clamping device.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The operator should pay particular and additional
attention to these points in order to reduce the risk of
serious personal injury.
■ Injury to hearing
NOTE: Wear suitable ear protection and limit exposure.
■ Injury to sight
NOTE: Wear protective eye shields or goggles when
using the product.
■ Injury caused by vibration
NOTE: Limit exposure and follow the instructions on
risk reduction in this manual.
■ Electric shock after contact with hidden wires
NOTE: Hold the product only by insulated surfaces.
■ Respiratory injury from dust created by operating the
product
NOTE: Wear suitable protection depending on type of
dust.
RISK REDUCTION
It has been reported that vibrations from handheld tools
may contribute to a condition called Raynaud’s Syndrome
in certain individuals. Symptoms may include tingling,
numbness and blanching of the fi ngers, usually apparent

Похожие устройства

Скачать