Safety Speed sr5ua Инструкция по эксплуатации онлайн [16/41] 198935

Proper preparation for long term storage is essential

for keeping your snow blower free from rust corrosion

and prevent part and function to parts impair. The

following steps will make the engine easier to start

after storage and prevent your snow blower from

rusting during long term storage.

Notice: The warranty does not cover damage on

machine or engine as a result of incorrect storage or

negligence to comply with maintenance

recommendation and warning.

Cleaning If the engine has been running, allow it to

cool for at least half an hour before cleaning. Clean all

exterior surfaces, seal up any damaged paint, and coat

other areas that may rust with a light film of oil.

Notice: Water directly on a hot engine can cause

damage or worse crack the aluminum parts in the

engine. If the engine has been running, allow it to cool

for at least half an hour before washing.

Fuel Gasoline will oxidize and deteriorate during

storage. Stale gasoline will cause hard starting, and

will leave gum deposits that will clog the fuel system.

Do not keep same gasoline in engine for more than

3 months!!!

Warning: Don’t start the engine with oxidize and

deteriorate gasoline in the fuel tank, it may damage the

carburetor and other fuel system components!

Preparation for long term storage

We recommend draining the fuel tank and carburetor

before long-term storage. However adding a fuel

stabilizer can extend fuel service life.

Draining the fuel tank and carburetor

We recommend draining the fuel tank first and

hereafter the carburetor.

How to:

1. Place an approved gasoline container below the

carburetor, and use a funnel to avoid spilling

fuel.

2. Remove the carburetor drain bolt, and then pull

out the fuel tube.

3. After all the fuel has drained into the container,

reattach the drain bolt and fuel tube. Ensure

that both bolt and tube are securely tightened.

Adding a fuel additive

Follow the fuel additive scale of the manufacturer.

How to:

1. Empty fuel tank for old gasoline and refill fresh.

2. Pour the fuel additive in the tank.

3. Idle run, the engine outdoors for 10 minutes.

This will blend the fuel mixture in the engine

block and carburetor.

4. Stop the engine.

Precautionary measures against moist

In order to minimize the parts to impair from moist:

1. Change the engine oil.

2. Remove the spark plugs.

3. Pour a tablespoon (5-10 cc) of clean engine oil

into the cylinder.

4. Pull the starter rope several times to distribute

the oil in the cylinder.

5. Reinstall the spark plugs.

6. Pull the starter rope slowly until resistance is

felt. This will close the valves so moisture

cannot enter the engine cylinder. Return the

starter rope gently.

General advice

• Select a well-ventilated storage location, with

low humidity in order to prevent rust and

corrosion.Avoid locations where an ignition

source is present.

• A drained fuel tank will, minimize the possibility

of fuel leakage.

• Position the equipment so the engine is level.

Tilting the machine can cause fuel or oil

leakage.

• Cover the engine and exhaust system to prevent

from dust.

Notice: A hot engine and exhaust system can ignite or

melt some materials. Do not use sheet plastic as a

dust cover. A nonporous cover will trap moisture

around the engine, promoting rust and corrosion.

Preparing the engine after a long term storage

• Check your engine as described under

maintenance

• Start your engine as described under operation.

Notic

e: G

asoline oxidizes and deteriorates over time,

causing hard starting. If the cylinders were coated with

oil during storage preparation, the engine may smoke

briefly at startup. This is normal.

Storage planner

Less than 1- month

• No special preparation is required.

1 to 2 months

• Fill with fresh gasoline and add a gasoline

conditioner.

2 months to 1 year

• Fill with fresh gasoline and add a gasoline

conditioner.

• Drain fuel from carburetor.

• Clean fuel sediment cup.

1 year or more

• Drain fuel tank and carburetor.

• Clean fuel sediment cup.

• Remove spark plug.

• Put a tablespoon of engine oil into the spark

plug cylinder. Turn the engine slowly with the

pull rope to distribute the oil. Reinstall spark

plug.

• Change Oil.

Safety Speed sr5ua Инструкция по эксплуатации онлайн [16/41] 198935

Похожие устройства