Timberk tec.ps1 el15 in (og) Инструкция по эксплуатации онлайн [5/26] 201664

Содержание

• Electric convector heater 1
• Timberk 1
• Модели models 1
• Руководство по эксплуатации instruction manual 1
• Электрический конвектор 1
• Русский 25
• Timberk 26

Похожие устройства

• Timberk tec.ps1 el10 in (og) Инструкция по эксплуатации
• Timberk tec.pf2 ml20 in (wb) Инструкция по эксплуатации
• Timberk tec.pf2 ml15 in (wb) Инструкция по эксплуатации
• Timberk tec.pf2 el20 in (bb) Инструкция по эксплуатации
• Timberk tec.pf2 el10 in (bb) Инструкция по эксплуатации
• Timberk tch a2 1100 Инструкция по эксплуатации
• Timberk tch a2 800 Инструкция по эксплуатации
• Timberk tor 31.1506 rr Инструкция по эксплуатации
• Timberk tih q2 2m Инструкция по эксплуатации
• Timberk tch a1n 2000 Инструкция по эксплуатации
• Timberk tch a1n 700 Инструкция по эксплуатации
• Timberk thu ul 03 o Инструкция по эксплуатации
• Timberk dh tim 30 e1w Инструкция по эксплуатации
• Timberk tef w16 wc2 Инструкция по эксплуатации
• Timberk tef t16 tc3 Инструкция по эксплуатации
• Timberk tef f18 fn4 Инструкция по эксплуатации
• Timberk tef f12 fh5 Инструкция по эксплуатации
• Timberk tor 31.2612 rm Инструкция по эксплуатации
• Timberk tor 31.2309 rm Инструкция по эксплуатации
• Timberk tor 31.1807 rm Инструкция по эксплуатации

iiiiiiiiiiiiiiiuiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiim 6 INSTALLATION ENGLISH ЦИИШ Leg mounting ofthe convector Fig 7 1 Take 2 legs out of a package box 2 Turn overthe unit so that its lower part was at 3 Attach legs to the lower part ofthe unit from the left and right sides so that the mounting holes coincide with holes on the unit s case 4 Fasten mounting screws in the present holes exerting enough force Check security of 1 Open the factory package and carefully remove the unit out ofplace IL it on a smooth horizontal surface strictly in a itvertical 2 Remove seals out of foamed plastic on sides of the unit and take out of position polyethylene The unit Is ready to usel minimum distance from the floor 4 Mark the height at which the convector Is to be mounted thenI attach The convector Is designed to be connected to 220 240V single ph bracketto the wall voltage mains with agrounding circuit 5 Put visible marks in mounting holes 6 Drill holes of the required diameter on the mounting holes insert dowels identification plate with technical data ofthe unit bracket on thewall Fig 5 3 It is necessary to follow active electrical safety precautions conn 7 Suspend the convector on the bracket for which purpose attach lower the the convectorto electric mains part of the unit to the lower extension of the bracket and Insert them 4 Aninto electric outlet must be properly grounded The outlet must be slots available in the lower part of the unit s rear panel Carryingdesigned out thesefor rated current not less than 10A Electric outlet and plug always stay dry to prevent current leakage Regularly check if the e plug is tightly connected to the outlet It must be done In the followin the unit until you hear clicking of the upper extensions Fig 6 9 To dismount the unit press the leverages of the bracket s upper plug is heated by your hand If the plug heated over 50 C then repla extensions and disconnect the unit from it Then carry out the outlet by a new one to prevent damages incidents fire as a result o electric contact A specialist must do the job OIMPORTANTI Electric outlet must be designed for rated current not less tha 1OA electric cable with a stand with cross section not less th 3 15 mm2 for cooper