Magio MG-583 Инструкция по эксплуатации онлайн [16/20] 315631

Содержание

• Волосся мм 5
• Насадка довжина 5
• Волос мм 11
• Насадка длина 11
• Comb attachment hair length mm 17

Похожие устройства

• Magio MG-587 Инструкция по эксплуатации
• Hilton ICM 3851 Инструкция по эксплуатации
• Magio MG-582 Инструкция по эксплуатации
• Hilton ICM 3852 Инструкция по эксплуатации
• Magio MG-588 Инструкция по эксплуатации
• Magio MG-580 Инструкция по эксплуатации
• Magio MG-581 Инструкция по эксплуатации
• Hilton KS 3219 Инструкция по эксплуатации
• Magio MG-590 Инструкция по эксплуатации
• Hilton KS 3218 Инструкция по эксплуатации
• Magio MG-591 Инструкция по эксплуатации
• Magio MG-187 Инструкция по эксплуатации
• Magio MG-189 Инструкция по эксплуатации
• Magio MG-180N Инструкция по эксплуатации
• Hilton HL 4192 Инструкция по эксплуатации
• Magio MG-182N Инструкция по эксплуатации
• Hilton HL 4193 Инструкция по эксплуатации
• Magio MG-552 Инструкция по эксплуатации
• Hilton KA 5412 Инструкция по эксплуатации
• Magio MG-553 Инструкция по эксплуатации

ALIGNING THE BLADE All of our hair clippers are carefully checked at the factory The blades are aligned and lubricated with special oil included in the original set If the blades were removed for cleaning or replacement they must be aligned Align the blades in the plane and tighten the retainer screws The lower blade must come forward relative to the top one by 1 2 mm see the figure If you are unable to align the blades add a few drops of oil to them turn the clipper on for about 30 40 seconds then turn off the clipper and remove the plug from the outlet Loosen the screws that hold the lower blade a little and align the blades After aligning the blades don t forget to tighten the retainer screws of the lower blade LUBRICATING OIL To maintain the clipper in good working condition it is necessary to lubricate the blades after every use Do not use vegetable oil or oil that contains kerosene or other solvents Solvents evaporate and the heavy oil that remains can slow the motion of the blade Use only the oil included in the delivery set BLADE LEVER The blade displacement lever is conveniently located under the thumb if you are right handed During use you can depress the lever to move the blade thus regulating the length of the cut without using a comb attachment The top lever position allows the shortest cutting Pushing the lever downward gradually increases the cutting length In the bottom lever position the length of the cut is the same as when using comb attachment 3mm By changing the position of the lever while cutting you can select the necessary length of the cut Changing the position of the blade will extend its life If hairs get caught between the blades during use release them by moving the lever up and down a few times while the clipper is switched on This will help to free the hair without removing the blade If the clipper pulls hair this means that the blades are dull and you must replace them with new ones STYLING INSTRUCTIONS 1 Before beginning to cut hair make sure that the clipper works properly and the blades move smoothly 2 Remove excess lubricating oil from the blades with a dry cloth 3 Always be aware of the state of the power cord 4 Do not allow it to twist 5 If necessary turn off the clipper and straighten the cord 6 The person whose hair is being cut should sit with their head at your eye level their shoulders covered with a towel Comb the hair before cutting it REMINDER Cut a small amount of hair with each pass You can always return to the same place later Best results are obtained when the hair is dry BEGINNING TO CUT When cutting for the first time it is better to leave the hair somewhat long As you master the use of the clipper you will be able to style as desired