Tp-Link TL-SG1024 Инструкция по эксплуатации онлайн [14/28] 39022

Содержание

• Installation guide p.1
• Gigabit unmanaged switch p.1
• Fcc statement p.3
• Copyright trademarks p.3
• Ce mark warning p.3
• Related document p.4
• Conventions p.4
• Audience p.4
• About this installation guide p.4
• Appendix b specifcations 19 p.5
• Contents p.5
• Chapter 4 connection 16 p.5
• Chapter 1 introduction 01 p.5
• Appendix c technical support 20 p.5
• Appendix a troubleshooting 18 p.5
• Chapter 3 lightning protection 10 p.5
• Chapter 2 installation 05 p.5
• Product overview c1c p.6
• Introduction chacter c p.6
• Features c11 p.6
• Front panel p.7
• Accearance c11 p.7
• Note tl sg1048 has no 1000mbps leds while its link act leds can indicate port speed by flashing different colors green 1000mbps yellow 10 100mbps1 p.8
• Gigabit unmanaged switch p.8
• Designed to connect to the device with a bandwidth of 10mbps 100mbps or 1000mbps each has a corresponding link act led and a 1000mbps led tl sg1048 has no 1000mbps leds while its link act leds can indicate port speed by flashing different colors green 1000mbps yellow 10 100mbps1 p.8
• A 1000mbps device is connected to the corresponding port p.8
• A 10 100mbps device or no device is connected to the corresponding port p.8
• 100 1000mbps port p.8
• Tl sg1008 p.8
• The rear panel of tl sg1048 is shown as the following figure p.8
• The rear panel of tl sg1024 tl sg1016 is shown as the following figure p.8
• The front panel of tl sg1008 is shown as the following figure p.8
• Rear panel p.8
• Of tl sg1048 p.8
• Power socket p.9
• Grounding terminal p.9
• Safety precautions 111 p.10
• Safety precautions p.10
• Package contents 11c p.10
• Installation chacter 1 p.10
• Temperature humidity p.11
• Site requirements p.11
• Electromagnetic interference p.11
• Clearness p.11
• Lightening protection p.12
• Installation tools 111 p.12
• Installation site p.12
• Product installation 112 p.13
• Rack installation p.13
• Desktop installation p.13
• Requirements for cabling outdoors p.15
• Lightning protection chacter 1 p.15
• Cabling reasonably 11c p.15
• Requirements for the distance between ethernet cable and other pipelines are p.16
• Requirements for the distance between ethernet cable and high power electric p.16
• Requirements for cabling indoors p.16
• Note the above minimum net length height is required when metal raceway is not used if any requirements cannot be met you can add a steel tube or metal raceway for shielding p.16
• Gigabit unmanaged switch p.16
• Devices are in following tables p.16
• Cabling keep the loop area formed by the cable itself as small as possible p.16
• When cabling indoors keep a certain distance away from the devices that may cause high frequency interferences such as down conductor cable powerline power transformer and electromotor p.16
• The two diagrams below demonstrate parallel net length and parallel overlapping net height p.16
• The main cable should be paved in the metal raceway of the access shaft when p.16
• Shown in the table p.16
• In different environments the device may be grounded differently the following will instruct you to connect the device to the ground in two ways connecting to the grounding bar or connecting to the ground via the power cord please connect the device to ground in the optimum way according to your specific operation environment p.17
• If the device is installed in the equipment room where a grounding bar is available you are recommended to connect the device to the grounding bar as shown in the following figure p.17
• Connecting to the grounding bar p.17
• Connecting the device to ground is to quickly release the lightning over voltage and over current of the device which is also a necessary measure to protect the body from electric shock p.17
• Connect to ground 111 p.17
• Equicotential bonding 111 p.18
• Connecting to the ground via the power supply p.18
• Use lightning arrester 112 p.19
• Verify installation 211 p.21
• Power on 211 p.21
• Ethernet port 21c p.21
• Connection chacter 2 p.21
• Initialization 212 p.22
• The power led is not lit qqqq p.23
• The link act led is not lit when a device is connected to the qqqq corresconding cort p.23
• Accendix a troubleshooting p.23
• Ieee 802 u 100base tx p.24
• Ieee 802 ab 1000base t p.24
• Ieee 802 10base t p.24
• Gigabit unmanaged switch p.24
• Accendix b scecifications p.24
• To download the latest firmware driver utility and user guide please go to p.25
• Technical support p.25
• Www tp link com support download asp for all other technical support please contact us by using the following details p.25
• Gigabit unmanaged switch p.25
• For more help please go to www tp link com support faq asp p.25
• Accendix c technical succort p.25
• Gigabit unmanaged switch p.26
• Technical support p.26