Home
Главная
Scarlett
Машинка Для Стрижки
SC-HC63C45
Инструкция по эксплуатации Страница: 4

Scarlett SC-HC63C45 Инструкция по эксплуатации онлайн [4/19] 363375

IM020

www.scarlett.ru SC-HC63C45

GB INSTRUCTION MANUAL

IMPORTANT SAFEGUARDS

 Please read this instruction manual carefully

before use and keep in a safe place for future

reference.

 Before switching on the appliance for the first

time please check if the technical specifications

indicated on the unit correspond to the mains

parameters.

 For home use only. Do not use for industrial

purposes. Do not use the appliance for any other

purposes than described in this instruction

manual.

 Do not use outdoors.

 Always unplug the appliance from the power

supply before cleaning and when not in use.

 To prevent risk of electric shock and fire, do not

immerse the appliance in water or any other

liquids. If it has happened DO NOT TOUCH the

appliance, unplug it immediately and check in a

service center.

 Do not take this product to a bathroom or use

near water.

 The appliance is not intended for use for

physically, sensory or mental disabled person

(including children) or for person with lack of life

experience or knowledge, if only they are under

supervision or have been instructed about the

use of the unit by responsible person.

 Children must be under control in order not to be

allowed to play with the appliance.Do not leave

the appliance switched on when not in use.

 Do not use other attachments than those

supplied.

 Do not operate after malfunction or cord

damage.

 In case of power cord is damaged, its

replacement should be done by the manufacture

or service department or the other high-skill

person to avoid any danger.

 Do not attempt to repair, adjust or replace parts

in the appliance. Repair the malfunctioning

appliance in the nearest service center.

 Keep the cord away from sharp edges and hot

surfaces.

 Do not place or store the appliance where it can

fall or be pulled into a tub or sink.

 Do not pull, twist, or wrap the power cord around

the appliance.

 Never insert any objects into openings in the

appliance housing.

 Do not put operating appliance on any surface, it

may cause injury or damage.

 Do not use the appliance with damaged comb, or

with teeth missing from the blades as injury may

occur.

 If the product has been exposed to temperatures

below 0ºC for some time it should be kept at

room temperature for at least 2 hours before

turning it on.

 NOTE: KEEP THE BLADES OILED.

 Do not use the hair clipper when the skin is

infected.

 Do not use the hair clipper on animals.

 The manufacturer reserves the right to introduce

minor changes into the product design without

prior notice, unless such changes influence

significantly the product safety, performance,

and functions.

 Manufacturing date is indicated on the unit

and/or on packing as well as in accompanying

documents in the following format XX.XXXX

where first two figures XX is the month of

production, and following four figures XXXX is

the year of production.

BLADE ALIGNMENT

 Blades must be realigned if they were removed

for cleaning or after replacement.

 To realign the blades, simply match the upper

and lower blades teeth up, point for point.

 End of top blade teeth should be approximately

1.2 mm back from lower blade. Compare your

clipper blades with the sketch (pic.1).

 If blade alignment is incorrect, add a few drops

of oil to the blades, switch on the clipper for a

few moments, switch off and unplug. Loosen

screws slightly and adjust. Tighten screws after

blade is aligned.

OILING

 To maintain your clipper in peak condition, the

blades should be oiled after every haircut.

 Do not use hair oil, grease, oil mixed with

kerosene or any solvent.

BLADE LEVER

 The lever located to the left of the blades, allows

easily adjust cut hair length while clipping.

 The lever adds versatility to your clipper by

allowing you gradually change the closeness of

your cut without an attachment comb.

 When the lever is in the uppermost position, the

blades will give you the closest cut and leave the

hair very short. Pushing the lever downwards

gradually increases the cutting length.

 In its lowest position, the lever will leave the hair

approximately the same length as a №1 (3mm)

comb.

 The lever will also extend the use of your blades

since a different cutting edge is used in each

setting.

 In addition, if extremely heavy hair cutting has

jammed the blades, it will help you to remove

hair that has become wedged between the two

blades without removing the blades.

 While the clipper is running rapidly move the

lever from “close cut” to “longer cut” a couple of

times. Do this each time after you have finished

using your clipper to keep the blades free of cut

hair.

 If this does not help and clipper stops cutting,

blades are dulled. Replace them with new

blades.

INSTRUCTIONS FOR HAIR CUTTING

 Before first use cutting blades of the machine

should be thoroughly lubricated.

 Wipe off any excess oil. This should be done

after each use. While using the unit, untwist the

cord from time to time to avoid tangling.

Scarlett SC-HC63C45 Инструкция по эксплуатации онлайн [4/19] 363375

Содержание

Похожие устройства