Home
Главная
Zigmund & Shtain
Вытяжка островная
K 332.41 S
Инструкция по эксплуатации Страница: 8

Zigmund & Shtain K 332.41 S Инструкция по эксплуатации онлайн [8/24] 373463

The lters are not washable nor re-useable

and must be replaced at maximum every

four months.

To assemble the carbon lter it is necessary

to:

- remove the metal anti-grease lters

(Fig.4M)

- if present, extract the 'easy-clean' panel

(Fig.4N) by unscrewing the 4 screws.

- remove the carbon lter unscrewing the

screw (Fig.2)

INSTALLING INSTRUCTIONS

This hood has been arranged to be installed

above a cooktop. It can be used in 2 ways:

•EXHAUST MODE (Fig.3A): the kitcken va-

pours are puried by the metal anti-grease

lters and carried outside through a ducting

system.

•RECIRCULATING MODE (Fig.3B): the

kitcken vapours are puried by the metal

anti-grease lters and an activated carbon

lter (sold separately), then conveyed back

into the kitchen through the eyelets impres-

sed on the upper chimney.

We suggest to have installation carried out

by qualied personnel, in compliance with

all the current regulations and in particular

with the ones concerning air exhaust and

electrical connection.The manufacturer

cannot be held liable for damages caused

by improper installation or if it has not been

carried out according to the state-of-the-art.

IMPORTANT

•The appliance must be installed at a mini-

mum height of 650 mm from an electric coo-

ker stove, or 750 mm from gas or combined

cooker stoves (Fig.3).

•If a connection tube composed of two parts

is used, the upper part must be placed out-

side the lower part.

•Do not connect the cooker hood exhaust to

the same conductor used to circulate hot air

or for evacuating fumes from other applian-

ces generated by other than an electrical

source.

•Take care when the cooker hood is opera-

ting simultaneously with an open replace

or burner that depend on the air in the

environment and are supplied by other than

electrical energy, as the cooker hood remo-

ves the air from the environment which a

burner or replace need for combustion.

•Provide adequate ventilation in the envi-

ronment for a safe operation of the cooker

hood.

•Follow the local laws applicable for external

air evacuation.

•Use screws and screw anchors suitable for

wall (e.g. reinforced cement, plasterboard)

for the mounting of the cooker hood. Where

screws and screw anchors are supplied

ensure that they are suitable for the type

of wall where the cooker hood is to be

mounted.

COMPONENTS > see Fig.4

EXHAUST MODE INSTALLATION

• Drill the holes of the bracket Z to the

ceiling at the center of your cooktop. Lock

the Z bracket to the ceiling using 4 screws

(Fig. 5).

• Attach the telescopic lower H of the hood

C to the body with 4 screws (Fig. 6)

• Thread the upper connection E and within

the body of the hood C (Fig. 7)

• Attach the telescopic bracket G to the

bracket Z with 4 screws (Fig. 8)

• Attach the two side brackets U to the

telescopic structure than G with 2 screws on

both sides (Fig. 9)

• carry out for exhaust mode only

Connect through a connecting tube, the

ange of Ø 150 mm (Fig. 4Y) to the drain

hole. In the event that the apartment is

equipped with a pipe outside air connection

of Ø 210mm apply a reduction.

•Attach the telescope G to the lower H with

4 screws (Fig. 10). Adjust the height so that

the underside of the hood is at a distance

of not less than 650 mm from the cooking

surface (Fig. 3).

•Slide the upper connection and up and

secure with 4 screws in the holes of the

brackets U (Fig. 11).

RECIRCULATING MODE ISTALLATION

In order to transform your cooker hood

from the exhaust version to the recircula-

ting version, ask your local retailer for the

Zigmund & Shtain K 332.41 S Инструкция по эксплуатации онлайн [8/24] 373463

Содержание

Похожие устройства