![Invt CHV190-220G-4 Инструкция по эксплуатации онлайн [146/242] 471545](/img/pdf.png)
Invt CHV190-220G-4 Инструкция по эксплуатации онлайн [146/242] 471545
![Invt CHV190-5R5G-4 Инструкция по эксплуатации онлайн [146/242] 471528](/views2/1583099/page146/bg92.png)
CHV190 series special inverter for crane
- 145 -
buffer resistor. If the light is on, the fault may be lies in the switching power supply. Please
ask for support.
Power supply air switch trips off when power on:
◆ Inspect whether the input power supply is grounded or short circuit. Please solve the
problem.
◆ Inspect whether the rectify bridge has been burnt or not. If it is damaged, ask for
support.
Motor doesn’t move after inverter running:
◆ Inspect if there is balanced three-phase output among U, V, W. If yes, then motor could
be damaged, or mechanically locked. Please solve it.
◆If the output is unbalanced or lost, the inverter drive board or the output module may be
damaged, ask for support.
Inverter displays normally when power on, but switch at the input side trips when
running:
◆ Inspect whether the output side of inverter is short circuit. If yes, ask for support.
◆ Inspect whether ground fault exists. If yes, solve it.
◆ If trip happens occasionally and the distance between motor and inverter is too far, it is
recommended to install output AC reactor.
Содержание
- Contents 2
- Safety precautions 5
- Introduction 6
- Technology features 6
- Description of nameplate 7
- Selection guide 8
- Parts description 9
- Description of extension card 10
- Unpacking inspection 11
- Disassemble and installation 12
- Environmental requiremen 12
- Installation and commissioning 14
- Connections of peripheral devices 15
- Terminal configuration 16
- Typical wiring diagram 18
- Wiring the main circuits 19
- Wiring control circuit terminals 21
- Installation guidline to emc compliance 23
- Operation 27
- Operating keypad description 29
- Operation process 29
- Running state 31
- Detailed function description 33
- P0 group basic function 33
- P1 group speed curve 40
- P2 group motor parameters 44
- P3 group vector control 48
- P4 group encoder 53
- P5 group input terminals 54
- P6 group output terminals 60
- P7 group display interface 65
- P8 group enhanced function 69
- P9 group protection parameters 79
- Pa group serial communication 84
- Pb group master slave control group 88
- Pc group motor parameters 1 96
- Pd group profibus communication 100
- Pe group factory setting 104
- Pf group motor parameters 2 104
- Pp group motor parameters 3 108
- Description of chv190 s extension card 113
- Description of i o extension card 113
- Description of asynchronous pg card 114
- Description of synchronous pg card 118
- Description of modbus communication card 120
- 485 gnd 121
- Description of profibus communication card 122
- 4 3 2 1 126
- Address 4 parameter 137
- Parameter address 137
- Parameter changes 137
- Pkw1 pkw2 pkw3 pkw4 cw pzd2 pzd3 pzd12 00 01 00 04 00 00 00 xx xx xx xx xx xx xx xx 137
- Pkw1 pkw2 pkw3 pkw4 cw pzd2 pzd3 pzd12 00 02 00 04 00 00 50 xx xx xx xx xx xx xx xx 137
- Request read parameter 137
- Requst 137
- Pkw1 pkw2 pkw3 pkw4 cw pzd2 pzd3 pzd12 00 01 00 04 00 00 50 xx xx xx xx xx xx xx xx 138
- Response 138
- Response parameter values refreshed 138
- Ethernet communication description 139
- Fault and trouble shooting 140
- Trouble shooting 140
- Common faults and solutions 145
- Daily maintenance 147
- Maintenance 147
- Periodic maintenance 148
- Replacement of wearing parts 149
- Communication modes 150
- Communication protocol 150
- Interfaces 150
- Protocol format 150
- Protocol function 151
- Crc check 156
- Notice 156
- Example 157
- A open loop sequence 163
- Appendix a application mode description 163
- A close loop sequence 164
- Appendix b application mode description 166
- B general application mode 166
- B operating lever mode 166
- B remote control mode 168
- B hierarchical operating lever mode 169
- B hierarchical remote control mode 170
- B electric potential mode 172
- B master slave power equilibrium host mode 173
- B master slave power equilibrium slave mode 177
- B master slave speed synchronization host mode 178
- B master slave speed synchronization slave mode 181
- Appendix c the selection guide of chv190 183
- C inverter capacity calculation 183
- C renewable energy treatment 184
- Appendix d relative dimension of inverter 188
- D external dimension 188
- D dimensions of external keypad 189
- D installation space 190
- D disassembly 191
- Appendix e specifications of accessories 192
- E specifications of breaker cable contactor and reactor 192
- Appendix f functon parameters 195
Похожие устройства
- Invt CHV190-250G-4 Инструкция по эксплуатации
- Invt CHV190-280G-4 Инструкция по эксплуатации
- Invt CHV190-315G-4 Инструкция по эксплуатации
- Invt CHV190-350G-4 Инструкция по эксплуатации
- Invt CHV190-400G-4 Инструкция по эксплуатации
- Invt CHV190-500G-4 Инструкция по эксплуатации
- Invt GD300-1R5G-4 Инструкция по эксплуатации
- Invt GD300-2R2G-4 Инструкция по эксплуатации
- Invt GD300-004G-4 Инструкция по эксплуатации
- Invt GD300-5R5G-4 Инструкция по эксплуатации
- Invt GD300-7R5G-4 Инструкция по эксплуатации
- Invt GD300-011G-4 Инструкция по эксплуатации
- Invt GD300-015G-4 Инструкция по эксплуатации
- Invt GD300-018G-4 Инструкция по эксплуатации
- Invt GD300-022G-4 Инструкция по эксплуатации
- Invt GD300-030G-4 Инструкция по эксплуатации
- Invt GD300-037G-4 Инструкция по эксплуатации
- Invt GD300-045G-4 Инструкция по эксплуатации
- Invt GD300-055G-4 Инструкция по эксплуатации
- Invt GD300-075G-4 Инструкция по эксплуатации