![Qtech QSW-8200-28T-AC — руководство пользователя: Настройка сетевых портов и команд [17/85]](/img/pdf.png)
Qtech QSW-8200-28T-AC — руководство пользователя: Настройка сетевых портов и команд [17/85]
Превью страниц
Страница 17 /
85
![Qtech QSW-8200-52T-AC-DC Команды для настройки портов онлайн [17/85] 481624](/views2/1596641/page17/bg11.png)
User Manual
Chapter 1. Commands for Network Port Configuration 17
www.qtech.ru
module; auto-detected: automatic detection; no-phy-integrated: there is no phy-
integratd 100Base-FX module; phy-integrated: phy-integratd 100Base-FX module;
force1g-half is the forced 1000Mbps speed at half-duplex mode; force1g-full is the
forced 1000Mbps speed at full-duplex mode; nonegotiate disables auto-negotiation
forcibly for 1000Mb port; master forces the 1000Mb port to be master mode; slave
forces the 1000Mb port to be slave mode. force10g-full is the forced 10000Mbps speed
at full-duplex mode.
Command mode: Port Mode.
Default: Auto-negotiation for speed and duplex mode is set by default.
Usage Guide: This command is configures the port speed and duplex mode. When
configuring port speed and duplex mode, the speed and duplex mode must be the
same as the setting of the remote end, i.e., if the remote device is set to auto-
negotiation, then auto-negotiation should be set at the local port. If the remote end is
in forced mode, the same should be set in the local end.
1000Gb ports are by default master when configuring nonegotiate mode. If one end is
set to master mode, the other end must be set to slave mode.
force1g-half is not supported yet.
Example: Port 1 of Switch1 is connected to port 1 of Switch2, the following will set both
ports in forced 100Mbps at half-duplex mode.
Switch1(config)#interface ethernet1/0/1
Switch1(Config-If-Ethernet1/0/1)#speed-duplex force100-half
Switch2(config)#interface ethernet1/0/1
Switch2(Config-If-Ethernet1/0/1)#speed-duplex force100-half
1.1.18 storm-control
Command: storm-control {unicast | broadcast | multicast} <packets>
no storm-control {unicast | broadcast | multicast}
Function: Sets the traffic limit for broadcasts, multicasts and unknown destination
unicasts on all ports in the switch; the no command disables this traffic throttle
function on all ports in the switch, i.e., enables broadcasts, multicasts and unknown
destination unicasts to pass through the switch at line speed.
Parameters: use unicast to limit unicast traffic for unknown destination; multicast to
limit multicast traffic; broadcast to limit broadcast traffic. <packets> is the limit of
packet number, ranging from 1 to 1488905. For non-10GB ports, the unit of <packets>
is PPS, that is, the value of <packets> is the number of packets allowed to pass per
second; for 10GB ports, the unit is KPPS, that is, the value of <packets> multiplies 1000
makes the number of packets allowed, so the value should be less than 14880.
Command mode: Port Mode.
Default: No limit is set by default. So, broadcasts, multicasts and unknown destination
unicasts are allowed to pass at line speed.
Usage Guide: All ports in the switch belong to a same broadcast domain if no VLAN has
been set. The switch will send the above mentioned three traffics to all ports in the
Содержание
- Chapter 1 commands for network port configuration 7 p.2
- Show isolate port group 21 p.2
- Chapter 2 commands for port isolation function 20 p.2
- Loopback detection specified vlan 25 p.2
- Loopback detection interval time 24 p.2
- Loopback detection control recovery timeout 24 p.2
- Loopback detection control 23 p.2
- Isolate port group switchport interface 20 p.2
- Isolate port group 20 p.2
- Isolate port apply 21 p.2
- Debug loopback detection 23 p.2
- Content p.2
- Commands for ethernet port configuration 7 p.2
- Chapter 3 commands for port loopback detection function 23 p.2
- Show loopback detection 25 p.2
- Configuration p.7
- Commands for ethernet port configuration p.7
- Chapter 1 commands for network port p.7
- Isolate port group switchport interface p.20
- Isolate port group p.20
- Chapter 2 commands for port isolation function p.20
- Show isolate port group p.21
- Isolate port apply p.21
- Loopback detection control p.23
- Function p.23
- Debug loopback detection p.23
- Chapter 3 commands for port loopback detection p.23
- Loopback detection interval time p.24
- Loopback detection control recovery timeout p.24
- Show loopback detection p.25
- Loopback detection specified vlan p.25
- Debug uldp event p.26
- Debug uldp error p.26
- Debug uldp p.26
- Chapter 4 commands for uldp p.26
- Debug uldp packet p.27
- Debug uldp interface ethernet p.27
- Debug uldp fsm interface ethernet p.27
- Uldp enable p.28
- Uldp aggressive mode p.28
- Uldp manual shutdown p.29
- Uldp hello interval p.29
- Uldp disable p.29
- Uldp reset p.30
- Uldp recovery time p.30
- Show uldp p.30
- Debug lldp packets p.32
- Debug lldp p.32
- Clear lldp remote table p.32
- Chapter 5 commands for lldp function p.32
- Lldp mode p.33
- Lldp enable port p.33
- Lldp enable p.33
- Lldp notification interval p.34
- Lldp neighbors max num p.34
- Lldp msgtxhold p.34
- Lldp transmit optional tlv p.35
- Lldp transmit delay p.35
- Lldp toomanyneighbors p.35
- Lldp tx interval p.36
- Lldp trap p.36
- Show debugging lldp p.37
- Show lldp p.37
- Show lldp neighbors interface ethernet p.38
- Show lldp interface ethernet p.38
- Show lldp traffic p.39
- Interface port channel p.40
- Debug port channel p.40
- Chapter 6 commands for port channel p.40
- Lacp timeout p.41
- Lacp system priority p.41
- Lacp port priority p.41
- Port group mode p.42
- Port group p.42
- Load balance p.42
- Show port group p.43
- Chapter 7 commands for mtu p.45
- Chapter 8 commands for efm oam p.46
- Debug ethernet oam fsm p.46
- Debug ethernet oam error p.46
- Clear ethernet oam p.46
- Ethernet oam p.47
- Debug ethernet oam timer p.47
- Debug ethernet oam packet p.47
- Ethernet oam errored frame threshold low p.48
- Ethernet oam errored frame threshold high p.48
- Ethernet oam errored frame window p.49
- Ethernet oam errored frame period threshold low p.49
- Ethernet oam errored frame period threshold high p.49
- Ethernet oam errored frame seconds threshold high p.50
- Ethernet oam errored frame period window p.50
- Ethernet oam errored frame seconds window p.51
- Ethernet oam errored frame seconds threshold low p.51
- Ethernet oam errored symbol period threshold high p.52
- Ethernet oam errored symbol period threshold low p.52
- Ethernet oam link monitor p.53
- Ethernet oam errored symbol period window p.53
- Ethernet oam remote failure p.54
- Ethernet oam period p.54
- Ethernet oam mode p.54
- Ethernet oam remote loopback supported p.55
- Ethernet oam remote loopback p.55
- Show ethernet oam p.56
- Ethernet oam timeout p.56
- Show ethernet oam events p.61
- Show ethernet oam link events configuration p.64
- Show ethernet oam loopback status p.65
- Bpdu tunnel stp p.67
- Bpdu tunnel gvrp p.67
- Bpdu tunnel dmac p.67
- Chapter 9 commands for bpdu tunnel p.67
- Bpdu tunnel uldp p.68
- Bpdu tunnel lacp p.68
- Bpdu tunnel dot1x p.68
- Description language province state city county street locationnum location floor room postal otherinfo p.70
- Civic location p.70
- Chapter 10 commands for lldp med p.70
- Lldp med fast count p.71
- Ecs location p.71
- Lldp transmit med tlv capability p.72
- Lldp transmit med tlv all p.72
- Lldp med trap p.72
- Lldp transmit med tlv inventory p.73
- Lldp transmit med tlv extendpoe p.73
- Network policy p.74
- Lldp transmit med tlv networkpolicy p.74
- Show lldp p.75
- Show lldp neighbors p.77
- Clear port security p.78
- Switchport port security p.78
- Show port security p.78
- Chapter 11 commands for port security p.78
- Switchport port security mac address p.79
- Switchport port security aging p.79
- Switchport port security maximum p.80
- Switchport port security mac address sticky p.80
- Switchport port security violation p.81
- Show transceiver p.82
- Debug transceiver p.82
- Clear transceiver threshold violation p.82
- Chapter 12 commands for ddm p.82
- Show transceiver threshold violation p.83
- Transceiver monitoring p.83
- Transceiver threshold p.84
- Transceiver monitoring interval p.84
Похожие устройства
-
Qtech QSW-1500-20EF-POE-ACТехнические характеристики -
Qtech QSW-1500-19EF-POE-AC V3Описание параметров
-
Qtech QSW-1500-10E-POE-DОписание параметров
-
Qtech QSW-1500-6E-POE-DПодробное техническое описание
-
Qtech QSW-4610Инструкция пользователя -
Qtech QSW-3750 REV. RИнструкция пользователя
-
Qtech QSW-3750Руководство по эксплуатации
-
Qtech QSW-3420Инструкция по применению
-
Qtech QSW-9000-01Руководство по управлению -
Qtech QSW-9000-01Руководство по настройке -
Qtech QSW-9000-01Руководство по настройке управления -
Qtech QSW-9000-01Руководство по командам
Изучите команды для конфигурации сетевых портов, включая настройку скорости и дуплекса. Узнайте, как управлять трафиком и ограничениями на портах.