Home
Главная
Planet
Коммутаторы
FGSW-1820CS
Инструкция по эксплуатации Страница: 24

Planet FGSW-1820CS Инструкция по эксплуатации онлайн [24/68] 65342

- 24 -

Figure 4-12 Firmware Update Web page Screen

Then the following screen appears, press “Browser” button to find the firmware location administrator PC, the screen in

Figure 4-13 appears.

Figure 4-13 Firmware Update Web Page Screen

Содержание

24 port 10 100mbps with 1
Fgsw 1820cs fgsw 2620cs 1
Gigabit tp sfp combo 1
User s manual 1
Web smart switch 1
Ce mark warning 2
Disclaimer 2
Fcc warning 2
Revision 2
Trademarks 2
Weee warning 2
Table of contents 3
About the switch 4
Checklist 4
Introduction 4
Features 5
Specification 6
Front panel 8
Hardware description 8
Led indicators 8
Per 10 100 1000base t port sfp interfaces 8
Per 10 100mbps port 8
System 8
Desktop installation 9
Hardware installation 9
Notice 9
Power notice 9
Rear panel 9
Caution 10
Installing the sfp transceiver 10
Rack mounting 10
Notice 11
Notice 12
Management method 13
Overview 13
Planet smart discovery utility 13
Switch management 13
Web management 13
Notice 14
Logging on to the fgsw 1820cs fgsw 2620cs 15
Notice 15
Login in to the switch 16
Notice 16
Web management 16
Object description 18
System 18
Notice 19
System information 19
Ip configuration 20
Notice 21
Password setting 21
Factory default 22
Firmware update 23
Notice 25
Reboot 26
Object description 27
Port management 27
Port configuration 28
Object description 29
Object description 30
Port mirroring 30
Bandwidth control 31
Object description 31
Broadcast storm control 32
Object description 32
Object description 33
Port statistics 33
Vlan setting 34
A switch port can have only one pvid but can have as many vid as the switch has memory in its vlan table to store them 35
Adding an ieee802 q tag 35
All vlan groups share the same layer 2 learned mac address table 35
Base on the switch chipset specification the switch supports svl shared vlan learning 35
Because some devices on a network may be tag unaware a decision must be made at each port on a tag aware device before packets are transmitted should the packet to be transmitted have a tag or not if the transmitting port is connected to a tag unaware device the packet should be untagged if the transmitting port is connected to a tag aware device the packet should be tagged 35
Default vlans 35
Every physical port on a switch has a pvid 802 q ports are also assigned a pvid for use within the switch if no vlan are defined on the switch all ports are then assigned to a default vlan with a pvid equal to 1 untagged packets are assigned the pvid of the port on which they were received forwarding decisions are based upon this pvid in so far as vlan are concerned tagged packets are forwarded according to the vid contained within the tag tagged packets are also assigned a pvid but the pvid is not used to make packet forwarding decisions the vid is 35
Notice 35
Packets that are tagged are carrying the 802 q vid information can be transmitted from one 802 q compliant network device to another with the vlan information intact this allows 802 q vlan to span network devices and indeed the entire network if all network devices are 802 q compliant 35
Port vlan id 35
Tag aware switches must keep a table to relate pvid within the switch to vid on the network the switch will compare the vid of a packet to be transmitted to the vid of the port that is to transmit the packet if the two vid are different the switch will drop the packet because of the existence of the pvid for untagged packets and the vid for tagged packets tag aware and tag unaware network devices can coexist on the same network 35
The ether type and vlan id are inserted after the mac source address but before the original ether type length or logical link control because the packet is now a bit longer than it was originally the cyclic redundancy check crc must be recalculated 35
The switch initially configures one vlan vid 1 called default the factory default setting assigns all ports on the switch to the default as new vlan are configured in port based mode their respective member ports are removed from the default 35
Object description 36
Vlan settings 36
Port based vlan 37
Object description 38
Port based vlan setting example 38
Setup steps 38
Vlan scenario 38
Q vlan 39
Object description 40
Object description 41
Notice 42
Q vlan setting example 42
Two separate 802 q vlan with overlapping area scenario 45
Mtu vlan 48
Object description 48
It allows a maximum of 4 ports to be aggregated at the same time and up to 2 groups if the group is defined as a local static link aggregation group then the number of ports must be the same as the group member ports 49
Object description 50
Trunk setting 50
Object description 51
Qos setting 51
Object description 52
Priority mode 52
Class of service configuration 53
Object description 53
Vlan priority tag value define 53
Af assured forwarding 54
Ip tos dscp priority value define 54
Tcp udp port based qos 55
Object description 56
Object description 57
Security filter 57
Mac address filter 58
Object description 58
Tcp udp filter 59
Allow to choose list protocol for filtering 60
Object description 60
Misc operation 61
Object description 61
Logout 62
Address table 63
Auto negotiation 63
Forwarding filtering 63
Learning 63
Store and forward 63
Switch operation 63
Base tx port link led is lit but the traffic is irregular 64
How to deal forgotten password situation of fgsw 1820cs fgsw 2620cs 64
Performance is bad 64
Some stations cannot talk to other stations located on the other port 64
The link led is not lit 64
Troubleshooting 64
Why the switch doesn t connect to the network 64
A rj 45 cable pin assignment 65
A switch s rj 45 pin assignments 65
Appendix a networking connection 65
Ec declaration of conformity 67
Planet technology corporation 67
Ec declaration of conformity 68
Planet technology corporation 68

Planet FGSW-1820CS Инструкция по эксплуатации онлайн [24/68] 65342

Содержание

Похожие устройства