Cecotec Conga 7090 IA Cyclone Инструкция по эксплуатации онлайн [24/34] 549070
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Cecotec Conga 7090 IA Cyclone Инструкция по эксплуатации онлайн [24/34] 549070

Cecotec Conga 7090 IA Cyclone Инструкция по эксплуатации онлайн [24/34] 549070
4746
7090 7090
ENGLISH ENGLISH
Note: The robot cleans in an organised way and per 4x4 m squared areas, therefore it might
leave the room where it is cleaning to nish o the delimited area. Do not worry, the robot
will clean all the accessible surface.
Back home mode
Press the back home button.
This mode can be activated during any other cleaning cycle and the robot will stop cleaning
and return to the charging automatically.
The robot will take the shortest route back to the charging base thanks to its map saving and
the smart back home function.
When a cleaning cycle has been completed or the robot’s battery is low, thanks to its Total
Surface 3.0 technology, the robot will also return to the charging base to avoid running out of
battery. Once the robot has recharged, it will resume cleaning from the point it has stopped.
Recommendation: Remove the Wet & dry tank during charging.
Remote control
Fig. 16.
Schedule
Power levels (Turbo/Normal/Eco)
Back home
Clock
Manual control
On/Pause
Edge mode
Remote control binding
If the robot does not respond to the remote control, follow the below steps:
Press the Edge mode button on the remote control for 5 seconds for the remote control to
enter pairing mode. The screen will display 8888.
The remote receiver will be activated in 5 seconds and will enter pairing mode. The remote
control’s signal is received, and the remote control returns to normal status. The display will
show pairing is completed.
If the pairing process is unsuccessful, the remote control will display 8888 and will exit the
pairing mode after 30 seconds.
The following modes and operations can be activated from the remote control.
Modes
The rst time the robot is operated, it will map and save the whole house’s map by means of
its laser before starting the cleaning cycle. Use the robot in Auto mode and Eco power level,
this way you will ensure the robot saves the full map.
Note: Make sure the light indicator is lit up in blue before starting cleaning, indicating it is
activated. If not, press any button on the remote control to wake it up.
Auto mode
Fig. 17.
Press the power button on the remote control for it to start cleaning automatically, rst
a cleaning cycle in Edge mode and then another cycle in and organised zigzag motion,
recognising which areas it has cleaned and which ones it has not. The robot will automatically
plan the cleaning route as it is cleaning. If during this mode the robot is controlled manually,
the robot will calculate the route again and could go through previously cleaned areas. In
order to ensure ecient cleaning, do not operate it manually during auto mode cleaning. 
Thanks to its Total Surface 3.0 technology, if the battery is low during the cleaning cycle, the
robot will smartly return to the charging base automatically and, once it is fully charged, it
will resume the cleaning process from the same point, oering a high-eciency cleaning.
During cleaning, the robot will stop briey to evaluate the area and calculate the cleaning
route (this stop will vary depending on the house conditions).
Note: The robot cleans in an organised way and per 4x4 m squared areas, therefore it might
leave the room where it is cleaning to nish o the delimited area. Do not worry, the robot
will clean all the accessible surface.
Edge mode
Fig. 18.
Press the Edge mode button on the remote control for the robot to start cleaning under this
mode. It will automatically start cleaning along all the surface’s perimeters and then will
return to the charging base direct and automatically. If the robot has not started cleaning
from the charging base, it will return to the starting point.
Note: Press the power levels button to switch between the 3 modes: Turbo/Normal/Eco.
Back home mode
Fig. 19.
Press the Back-home button on the remote control in order to send the robot to the charging
base. This function can be activated during any other cleaning cycle and the robot will
automatically return to the charging base and stop the cleaning process. The robot will take
the shortest route back to the charging base thanks to its map saving and the smart back
home function. 
When a cleaning cycle has been completed or the robot’s battery is low, thanks to its Total
Surface 3.0 technology, the robot will also return to the charging base to avoid running out of
battery. Once the robot has recharged, it will resume cleaning from the point it has stopped.

Содержание

Похожие устройства

Скачать