Home
Главная
Bort
Ленточная Шлифовальная Машина
BBS-800-T
Инструкция по эксплуатации Страница: 7

Bort BBS-800-T Инструкция по эксплуатации онлайн [7/30] 560606

turn it on and o. Any power tool that cannot be

controlled with the switch is dangerous and must

be repaired.

• Disconnect the plug from the power source and/

or the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools. Such preventive safety

measures reduce the risk of starting the power

tool accidentally.

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

• Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may aect the power

tool’s operation. If damaged, have the power tool

repaired before use. Many accidents are caused

by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edg-

es are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to

be performed. Use of the power tool for opera-

tions dierent from those intended could result in

a hazardous situation.

Service

Have your power tool serviced by a qualied repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is main-

tained.

BEFORE USE

Installation of sanding belt

ATTENTION! Always unplug the machine’s power

cord from the electrical outlet when for a long time

you do not work with this tool before replacing

sanding belt as well as before cleaning, setting up

or repairing tool.

ATTENTION! Before installing a new sanding belt,

you must clean the sanding pad and rollers from

dust and dirt.

• Pull the belt tension lever (8). Be careful, because

lever in The tensioned position may slip back to the

closed position. Pull lever until it is locked.

• Take a sanding belt of the required size and grit.

With using the arrows on the inside of the sanding

belt, determine the direction of its movement.

• Put on the sanding belt, taking into account the

direction of its movement on leading and driven

rollers by holding it from the outside of the bottom

plate grinding machine.

• Ensure that the sanding belt is centered on the

bottom plate, and that the arrows correspond to

the direction of movement of the tape. Let goten-

sion lever.

NOTE: Be careful, because the position of the ten-

sion lever depends from spring tension. Make sure

that the tension lever is fully lowered.

Adjusting the position of the sanding belt.

• Turn on the sander and let the machine run for

7-10 seconds. idle.

• Turn the tool over with the grinding belt. Rotating

adjusting screw (6) left or right, adjust tape position

so that its edges protrude at 1-3mm beyond the

outer edges of both rollers.

ATTENTION! If the sanding belt during tool opera-

tion will being too close to the inside (base of the

rollers), this may cause wear, torn edges of the tape

and damage sanding machine.

Installing a dust collector

This machine is equipped with a outlet for dust (5)

and is completed cartridge dust collector. It is rec-

ommended to use this feature each when working

with the instrument, as well as wearing a respirator

and goggles.

Install a dust cartridge on the dust outlet or Con-

nect the nozzle with a special vacuum cleaner.

ATTENTION! It is necessary to regularly clean the

cartridge dust collector. Be extremely careful when

removing dust some materials in dusty form can be

explosive.

Mixtures of dust and oil or water may ignite over

time. Not overow the cartridge; remove dust from

the cartridge when it turns out to be about 2/3 full.

SAFETY WARNINGS FOR SANDER

• Use the machine only for dry sanding. Penetration

of water into the machine increases the risk of an

electric shock.

• Caution, re hazard! Avoid overheating the ob-

ject being sanded as well as the sander. Always

empty the dust collector before taking breaks. In

unfavourable conditions, e. g., when sparks emit

from sanding metals, sanding debris in the dust

bag, micro lter or paper sack (or in the lter sack

or lter of the vacuum cleaner) can self-ignite. Par-

ticularly when mixed with remainders of varnish,

polyurethane or other chemical materials and

when the sanding debris is hot after long periods

of working.

• Secure the workpiece. A workpiece clamped with

clamping devices or in a vice is held more secure

than by hand.

• Keep your workplace clean. Blends of materials

are particularly dangerous. Dust from light alloys

can burn or explode.

Bort BBS-800-T Инструкция по эксплуатации онлайн [7/30] 560606

Содержание

Похожие устройства